User Account

All Pages

Design circuit using limited number of components to achieve

Assignment Help Electrical Engineering
Reference no: EM13248809

a signal franging from 1khz to 100khz will be put into a davice that will need amplification that will output to speakers. A 12v battery is available as a power source, however the current out of the battery should be kept to a minimum. This 12v source will be in series with a 10 ohm resistor. Design a circuit using a limited number of components to achieve.

Reference no: EM13248809

Questions Cloud

Find out the molarity of an acetic acid solution : If you needed to determine the molarity of an acetic acid solution, CH3COOH, how would you proceed? CH3COOH(aq)+H2O(l) H3O^+(aq)+CH3COO^-(aq)
Determine the minimum number of poles : A pair of synchronous machines, on the same shaft, may be used to generate power at 60 Hz from the given source of power at 50 Hz. Determine the minimum number of poles that the individual machines
Explain cystathionine synthase and cystathionase levels : a liver biopsy demonstrates cystathionine synthase and cystathionase levels are normal. this patient may have a deficiency of
What is the average induced emf : A 7.5cm diameter circular loop of wire is in a 0.76T magnetic field. The loop is removed from the field in 0.21s, What is the average induced emf
Design circuit using limited number of components to achieve : a signal franging from 1khz to 100khz will be put into a davice that will need amplification that will output to speakers. A 12v battery is available as a power source, however the current out of the battery should be kept to a minimum.
How much charge would be on the plates : A 8.00?F parallel-plate capacitor with circular plates is connected to a 11.0V battery. How much charge would be on the plates if their separation were doubled while the capacitor remained connected to the battery
Determine the power delivered to the circuit : A 2560 - ? resistor and a 1.9 - ?F capacitor are connected in series across a generator (60.0 Hz, 120 V). Determine the power delivered to the circuit
Define a balanced equation for the neutralization : Write a balanced equation for the neutralization of each of the following: a)H3PO4(aq) and NaOH(aq) b)HI(aq) and LiOH(aq) c)HNO3(aq) and Ca(OH)2(s)
Find the number of turns in the secondary : A transformer is to be used to provide power for a computer disk drive that needs 5.8 V (rms) instead of the 120 V (rms) from the wall outlet. Find the number of turns in the secondary

Reviews

Write a Review

Electrical Engineering Questions & Answers

  What is the maximum effective data rate of the link

Consider a satellite communication link with a one way propagation delay of 300ms between the sender and receiver, operating at 10Mbps using packets of length 1500bytes. Length of the ACK packet is also 1500 bytes.

  The base class must as well have a virtual print

The base class must also have a virtual print() function that displays the class name. Randomly assign print functions in three other classes that display the class name. Create 7 pointers of the base class and have them point to all the classes.

  Use the bounce diagram to plot

The line is terminated in a load RL = 25 ohm. Use the bounce diagram to plot V(t) at a point midway along the length of the line from t = 0 to t = 25 ns.

  Design a collision free circuit for a router

A network router connects multiple computers together and allows them to send messages to each other. If two or more computers send messages simultaniously, they collide and the messages must be resent. Design a collision free circuit for a router..

  Define wireless networks

You want to download a 5 Mbit file over a 10-Mbps Rayleigh fading channel in the 1800 MHz frequency band. You are traveling at 6 km/h and use 1000-bit packets.

  Write vhdl for d flip-flop with synchronous active-low clear

Write the VHDL PROCESS statements for a D flip-flop with synchronous active-LOW clear, synchronous active-LOW preset, and responsive to a rising edge clock.

  Design a low-pass filter with a cutoff frequency

A) Design a low-pass filter with a cutoff frequency of 12 kHz. Use 0.15 uF capacitor and an appropriate resistor. B) Sketch and label the circuit. C) What is the gain of the filter at a frequency of 20 kHz Give your answer both as ratio (Vout/Vin) an..

  Determine equivalent circuit of transformer as low-voltage

The following test data were obtained from testing a 48kVA, 4800/240-V, step down transformer: Open-circuit test Voltage (V) 240 Current (A) 2 Power (W) 120 Short-circuit test Voltage (V) 150 Current (A)10 Current

  Determine the value of the output voltage

Determine the value of the output voltage due to the voltage source only (Vol), and due to the current source only (V02).

  Find the illumination

A lamp of 100 candela is placed 1 m below a plane mirror which reflects 90% of light falling on it. The lamp is hung 4 m above ground. Find the illumination.

  What is the piv rating for the diode

A 3.3V, 30 A dc power supply is to be designed with a ripple of less than 2.5%. Assume that a half-wave rectifier circuit (60 Hz) with a capacitor filter is used.

  What is the range of doping and pick a doping concentration

Restricting yourself to nondegenerate dopings and also requiring the resistance to be readily measured with a hand-held multimeter (say 1  R 1000), what is the range of doping Pick a doping concentration in the mid range.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd