Design a vdhl file controller to operate two separate sets

Assignment Help Electrical Engineering
Reference no: EM13247081

Design a VDHL file controller to operate two separate sets of three traffic light signals, one for each direction. Use eight LEDs as shown in to represent the outputs. The Time in This State can be met in several ways. One method is to use a debounced switch as input, another to input a 1 Hz clock, another to use the internal 24 MHz clock, and a frequency division circuit to create a 1 Hz output.

Green Lights = 5 s
Yellow lights = 1 s

Reference no: EM13247081

Previous Q& A

  How to calculate the ph of a solution containing formic acid

Calculate the pH of a solution containing 25.00 mL of 0.12 M formic acid (Ka = 1.7 x 10^-4) to which the following amounts of 0.10 M NaOH have been added

  Derive the characteristic equation for the ab latch

An AB latch operates as follows: If A = 0 and B = 0, the latch state is Q = 0; if either A = 1 or B = 1 (but not both), the latch output does not change; and when both A = 1 and B = 1, the latch state is Q = 1.

  Calculate the motors starting current

A 1000V, 50 hp compound motor runs at a speed of 750 rpm at full load. The armature, series and shunt field resistances are 0.5 ohm, 1 ohm, and 200 ohm, respectively. The motor efficiency at this condition is 80%. Calculate the motors starting cur..

  Calculate the starting torque of the motor

A dc series motor has a armature current of 10A at full load. The motor terminal voltage is 300V. The armature and field resistances are 2 ohm and 3 ohm respecitively. The motor speed at full load is 250 rpm. Calculate the starting torque of the m..

  Calculate developed torque at a full load armature current

A 600 V, dc shunt motor has armature and field resistance of 15 ohms and 600 ohms respectively. When the motor runs unloaded, the ine current is 3 A, and the speed is 1000rpm. Calculate the developed torque at a full load armature current of 50 A.

  Determine maximum energy store by capacitor

A parallel plate capacitor consists of 2 square plates 19 cm per side spaced .55 mm apart with only air between them. What is the maximum energy that can stored by the capacitor

  Explain how is high temperature defined

Is 373 K a high temperature? Some thermodynamic principles only hold at "high temperature". How is "high temperature" defined

  Calculate the distance the spring was compressed

A 1432.0 g mass is on a horizontal surface with μk = 0.44, Calculate the distance the spring was compressed. What is the velocity of the mass as it loses contact with the spring

  Explain what is the empirical formula of the compound

A sample of an unknown compound was analyzed and found to contain 19.97% phosphorus and oxygen - what is the empirical formula of the compound

  Determine the total charge on spherical shells

Two identical conducting spherical shells S1 and S2 carry charges Q1 and Q2, respectively, Determine the total charge on S1 and S2 after they are separated

Reviews

Write a Review

 

Similar Q& A

  Consider a communications channel with a passband

Consider a communications channel with a passband of 3 kHz to 27.4 kHz. A modem will be connected to this communications channel and the modem will operate with a signaling rate that is 0.56 the maximum allowable signaling rate for this communicat..

  What is the value of the voltage reflection coefficient

A certain lossless transmission line is terminated in a normalized load impedance of ZL,n = 0.5  j2 ohms. Use a Smith Chart to determine the answers to the following questions. Mark the position of the load impedance on the chart and label it ZL.

  Determine the sensitivity of junction depth to changes

how to determine the sensitivity of junction depth to changes in furnace temperature by calculating (dxj/xj)/(dT/T) for a drive diffusion.

  Define a three-phase overhead transmission line

A three-phase overhead transmission line has a per-phase resistance of 0.15 ohm/km, and a per-phase inductance of 1.3263 mH/km.

  Write an instruction sequence to subtract the 4-byte number

Write an instruction sequence to subtract the 4-byte number stored in memory locations 0x10-0x13 from the 4-byte number stored in memory locations 0x00-0x03 and store the difference in memory locations 0x20-0x2

  Determine what is the peak voltage of the signal

Consider the waveform equation: a. What is the frequency of the waveform (in Hz) b. What is the voltage Vx at a time t = 1.5 ms c. What is the voltage Vx at a time t = 3 ms d. What is the voltage Vx at a time t = 4.5 ms

  What is statistical process control and quality control

Give five examples of things that are measured in semiconductor manufacturing to help maintain quality. Explain how a prober can give a false reading. How is sort different than E-test.

  Find the frequency components at the output of the circuit

In a certain communications system a resonant-tuned circuit (tuned at 1200 kHz with Bandwidth = 15 kHz) is connected to the output of a non-linear amplifier (mixer). Find the frequency components at the output of the resonant-tuned circuit

  What is the length of stack pointer

The HL pair of 8085 microprocessor is loaded with 0505 H. The HL Pair is decremented to 000 H. Which flag will be affected (A)Z flag (B)C flag (C)No flag is affected (D)P flag 1.In a 8-bit Microcomputer having 8k bytes of RAM Memory,the length of sta..

  How long does doping take for an average hole to drift

A Si bar is 0.25 cm long and 500 ?m2 in cross-sectional area. It is grounded at x=0 and biased at +20V at x=0.25 cm. Find the resistance and the current at 300K (a) when the Si bar is doped with 2×1017 cm-3 arsenic

  Which has the higher resistance in copper wire

which has higher resistance: the copper wire that carries the power from Bonneville Dam to your circuit breaker box, the copper wire that carries the power from there to your computer, or the copper wire that runs from the from one side of the chi..

  Identify the output samples influenced by boundary effects

The frequencies of the tones are 100 Hz, 300 Hz, and 450 Hz. The sampling rate is 1 kHz. Describe a low pass, a band pass, and a high pass filter that could be used to detect the individual tones.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd