Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Consider four logical input lines(A,B,C, and D) to represent a fourbit decimal integer. The decimal value of this four bitinteger is to be shown on a seven segment display. You are to design a function to turn on one segment of the display.
Write a minimal sum of products logical expression that is true only when the center horizontal line is to be lit.
A 5-volt intelligence amplitude causes the frequency to change to ± 25 kHz. What will be the carrier frequency variation corresponding to an intelligence amplitude of 10 volts
The feedback capacitance of an inverting amplifier is 10pF. What is the Miller capacitance at the input if the gain of the amplifier is -120 What is the Miller capacitance at the output of the amplifier
Determine the transfer function for a first-order high filter with a cutoff frequency of 1000 radians per second and passband gain of 1 using the following types: a. 3-dB Butterworth type. b. Chebyshev type with 1 dB ripples on the passband.
a) Show how to implement a 4-to-1 multiplexer with an active high output and no enable using two of the 2-to-1 MUXes and a minimum number of additional gates. b) Repeat part (a) for a 4-to-1 multiplexer with an active low output.
All FSMs have an initial state and the FSM must be forced in to that initial state prior to processing any data inputs. Suppose you want to implement a 5-state FSM in a PAL16R4. Briefly describe how you would force the FSM into its initial state.
Design a circuit to compute F = (A*B*C) +3*D+12. where A,B,C and Dare 16-bit inputs, and F is a 16-bit output. Use 16-bit multiplier and adder components, and ignore overflow issues.
B.) Write an equation for v(t) for t > 0 C.) Write an equation for the power absorbed by resistor for t >= 0 D.) Find how much energy the resistor disspates for t >= 0 E.) How much energy is stored in capacitor at t=0
Design, simulate and program a 4-bit, 8-function ALU to implement the operations F2 F1 F0 Output Function S0 - S4 0 0 0 Output = A Input S = A 0 0 1 Output = A Complement S = NOT A 0 1 0 Output = A Plus B S = A + B0 1 1 Output = A Minus B S = A - B
Write C code that senses 3 accelerometer readings into pins PAD 8, 9 and 10 and displays them on the LCD. Also run a timer in seconds and log the values of the accelerometers in 3 arrays every second.
Assume you have a receiver with an overall noise figure of 23 dB and a bandwidth of 1 MHz. Assuming the minimum acceptable SNR at the output of the receiver is 6 dB, estimate the minimum detectable signal level in dBm at the receiver input.
One superhet, one homodyne, and one that downconverts to baseband receiver is operating in 700-750MHz. Pick a set of IF and LO frequencies, and identify any issues (images, spurs, LO harmonics in receiver band, services that interfere with IF)
The minimum useful bandwidth of the amplifier should range from 10Hz to 100KHZ, and this can be determined by the frequency of vin.The maximum peak value of vin is 0.5V. The specified coupling capacitors(non-polarized) are anticipated to comply wi..
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd