Calculate the highest velocityacceleration and jerk that

Assignment Help Mechanical Engineering
Reference no: EM13622107

A cam is to be desinged for an automated part loader.Using the motion equations,construct a chart that tabulates follower displacement versus time and cam rotation. Also plot this data when the prescribed motion for this application is as follows:

1) Rise 50mm in 1.5sec using the constant velocity motion scheme.

2) Return in 2.0 sec using the cycloidal moyion scheme.

3) Dwell for 0.75 sec .

4) Repeat the sequence.

a) Select a motion scheme that you recommend to the desinger ,And why.

b) Calculate the highest velocity,Acceleration and jerk that part would experience under that motion sheme.

c) Sketch a displacement curve ,and label the points.

Reference no: EM13622107

Questions Cloud

An electric car accelerates for 12 s by drawing energy from : an electric car accelerates for 12 s by drawing energy from its 400-v battery pack. during this time 1200 c of charge
However if she gives a medium or easy test there is a 05 : a professor gives tests that are either hard medium or easy. if she gives a hard test her next test will be either
Two protons are moving directly toward one another when : two protons are moving directly toward one another. when they are very far apart their initial speeds are 1.40 x 104
Under appropriate conditions the sampling distribution of : under appropriate conditions the sampling distribution of the z-statistic is approximately a standard normal
Calculate the highest velocityacceleration and jerk that : a cam is to be desinged for an automated part loader.using the motion equationsconstruct a chart that tabulates
Two kg of a mixture having an analyis of on a mass basis of : two kg of a mixture having an analyis of on a mass basis of 30 nitrogen 40 carbon dioxide 30 oxygen is compressed
From a horizontal distance of 00540 m a particle of mass : a charge of -2.78 oc is fixed in place. from a horizontal distance of 0.0540 m a particle of mass 9.02 x 10-3 kg and
The inner and outer surfaces of a cell membrane carry a : the inner and outer surfaces of a cell membrane carry a negative and positive charge respectively. because of these
Eight students were given a pretest to measure their public : eight students were given a pretest to measure their public speaking anxiety. then they completed a workshop to reduce

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the maximum velocity reached

A 0.7-lb block rests on top of a 0.5-lb block supported by but not attached to a spring of constant 9 lb/ft. The upper block is suddenly removed. Determine (a) the Maximum velocity reached by the 0.5-lb block, (b) the maximum height reached by the..

  Calculate the heat transfer and the work done

Saturated water vapor at 200oC is isothermally condensed to a saturated liquid in a piston-cylinder device. Calculate the heat transfer and the work done during this process in kJ/kg.

  An oven has five radiant heaters each one is rated at 15

an oven has five radiant heaters each one is rated at 15 kw. it should heat some 2-kg steel plates from 20 degrees

  Evaluate the variation of hoop stresses

Evaluate the variation of hoop stresses across the wall of the compound cylinder.

  If the power generated by the turbine is 4 mw determine the

steam expands in a turbine steadily at a rate of 25000 kgh entering at 6 mpa and 450degc and leaving at 20 kpa as a

  Heat transfer coefficient between gas and each wire is 200

a thermocouple is placed in an exhaust pipe in a diesel engine. thermocouple is reading 500oc while the exhaust pipe is

  How many of the ten gang members would need to fail the

lie detectors are sometimes used in criminal investigations but they do not function perfectly. if a suspect is guilty

  What is the satellites altitude

A satellite is in Earth orbit with an altitude at perigee of 555.0 km and an altitude at apogee of 1200.0 km. a. What is the semi-major axis of the orbit? b. What is the eccentricity? c. If the true anomaly is 160 degrees, what is the satellite's ..

  Determine the minimum tensile strength each cable must have

due to a poorly designed foundation the statue at point a slowly slides down a grass covered slope. to prevent further

  Explain compressive stress

Important information about Compressive Stress, A circular cross sectional bar with a diameter of 3.25 inches is loaded with a uniform axial compressive load of 22,750 pounds. What is the compressive stress along a cross section of the bar?

  Determine the energy change if the system mass

For the process where q= 62.5 kj/kg and wkcs= 60 kj/kg determine the energy change if the system mass is 2 kg.

  Find the actual and carnot thermal efficenciencies of this

a heat engine absorbs 25 mw from a 400 degree c combustion change and rejects 15 mw to the atmosphere at 30 degrees c.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd