Calculate the heat transfer and mass of water

Assignment Help Mechanical Engineering
Reference no: EM13706758

Water in a piston-cylinder assembly, initially at 1 bar and a quality of 65%, is heated at constant pressure until temperature reaches 200 degrees C. The work during the process is +300 kJ.

A. Show the process on a T versus v diagram.

B. Calculate the mass of water, in kg.

C. Calculate the heat transfer, in kJ.

Reference no: EM13706758

Questions Cloud

Re-construct the management-research question hierarchy : Identify the variables relevant to the study. In addition to the two variables shown on Page 2, what other variables would be relevant to the study and why? Classification variables count as well.
The most critical or important changes in society : What do you view as the most critical or important changes in society with the use of the technologies today?  this paper is for a class in ethics and technology.. 1000 words
Calculate delta velocity required to change the inclination : Calculate the delta velocity required to change the inclination of a circular orbit at 32,000 km altitude from a 28.5 degree inclination to an inclination of 45 degrees. Compute the propellant used if the satellite weighs 1200 lbs after the manoeuvre..
Changing the position of a satellite in an orbit : Calculate the change in velocity required in changing the position of a satellite in an orbit by 90 degrees. The initial and final orbit is circular around the Earth with a 15000 km radius. Calculate the delta velocity, semi-major axis and period for..
Calculate the heat transfer and mass of water : Water in a piston-cylinder assembly, initially at 1 bar and a quality of 65%, is heated at constant pressure until temperature reaches 200 degrees C. The work during the process is +300 kJ.
How much oil must be released from a press cylinder : How much oil must be released from a press cylinder with a 20 in bore to relieve the pressure from 2800 psi to 0 psi if the ram is extended 20 in? The compressibility of the fluid is .525% per thousand psi.
Find the final pressure : Steam at 300°C and 200 kPa is contained in a rigid tank of volume 0.36 m3. The tank is cooled while 350 kJ of heat are removed. Find the final pressure. Show the process on a P-v diagram
Brief stakeholder analysis narrative of the scenario : Brief stakeholder analysis narrative of the scenario described above considering different stakeholder groups that may benefit or be negatively impacted in this scenario.
Write a business case memo to the owner : Please assist with the following exercise.  "Your business uses all hubs. Users complain about slow network access. Write a business case memo to the owner justifying the purchase of switches to replace the hubs.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd