Assume that the mercury 50 operates on an ideal brayton

Assignment Help Mechanical Engineering
Reference no: EM13632391

Solar Turbines Mercury 50 Gas-Turbine power generator

Inlet air temperature: 300 K

Inlet air pressure: 100 kPa atmospheric value

Inlet air mass flow rate: 17.9 kg/s

Pressure ratio: 9.9

Fuel type: Natural gas

Fuel heating value: 43.3 MJ/m3

Fuel input rate: 0.21 kg/s

A)Assume that the Mercury 50 operates on an ideal Brayton cycle (no regeneration), and that the working fluid is air with variable specific heat, determine i) the thermal efficiency, ii) power output.

B) Repeat the analysis for part A, but assume that compressor and turbine each have a second law efficiency of 86%.

C)Repeat the analysis for part B, but now consider the regenerator between the compressor and combustion chamber, and that the outlet temperature of the exhaust gases leaving the regenerator (vented to the atmosphere) is 377 °C.

Reference no: EM13632391

Questions Cloud

Nitrogen gas in an expandable container is cooled from : nitrogen gas in an expandable container is cooled from 50.0degc to 10.0degc with the pressure held constant at 3.00 x
It is initially at a uniform temperature of 25 degc and is : a long stainless steel rod 18 cr 8 ni has a diameter of 6.4 mm. it is initially at a uniform temperature of 25 degc and
Suppose the us president wants an estimate of the : suppose the u.s. president wants an estimate of the proportion of the population who support his current policy toward
Air at 35degc 105 kpa flows in a 100 mm times 150 mm : air at 35degc 105 kpa flows in a 100 mm times 150 mm rectangular duct in a heating system. the volumetric flow rate is
Assume that the mercury 50 operates on an ideal brayton : solar turbines mercury 50 gas-turbine power generatorinlet air temperature 300 kinlet air pressure 100 kpa atmospheric
A cylinder has 01 kg air at 25oc 200 kpa with a 5 kg piston : a cylinder has 0.1 kg air at 25oc 200 kpa with a 5 kg piston on top. a valve at the bottom is opened to let the air out
Steam at 500 kpa 300c is used to heat cold water at 15c to : steam at 500 kpa 300c is used to heat cold water at 15c to 75c for domestic hot water supply. how much steam per kg
The fox tv network is considering replacing one of : the fox tv network is considering replacing one of itsprime-timecrime investigation shows with a new
Water at 15 mpa 150degc is throttled adiabatically through : water at 1.5 mpa 150degc is throttled adiabatically through a valve to 200 kpa. the inlet velocity is 5 ms and the

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd