Customer Service Chat
Get quote & make Payment
Power Engineering, Electrical Engineering
A three-phase transposed line is composed of one ACSR conductor per phase with flat horizontal spacing of 11 meters as shown in Figure (a). The conductors have a diameter of 3.625 cm. The line is to be replaced by a three-conductor bundle of ACSR. Each conductor of bundle is having the same diameter as the single-conductor line. The new line will also have a flat horizontal configuration, but it is to be operated at a higher voltage and therefore the phase spacing is increased to 14 m as measured from the center of the bundles as shown in Figure (b). The spacing between the conductors in the bundle is 45 cm. Determine
(a) The percentage change in the inductance.
(b) The percentage change in the capacitance.
Posted Date: 10/8/2012 8:27:47 AM | Location : United States
Ask an Expert
Power Engineering, Assignment Help, Ask Question on Power Engineering, Get Answer, Expert's Help, Power Engineering Discussions
Write discussion on Power Engineering
Your posts are moderated
Write your message here..
Perform octal subtraction, Q. Do as directed. a) Hexadecimal addition: ...
Q. Do as directed. a) Hexadecimal addition: 101 + ABC b) (43.25) 10-(89.75) 10 using 1's Complement c) Octal Subtraction 123-777 d) (123)6 + (435)6 = ( ? )6 e) ABC
Write a short note on heat sink, Q. Write a short note on heat sink For...
Q. Write a short note on heat sink For transistors handling small signals ,the power dissipated at the collector is small.Such transistors have little chances of thermal runawa
Antenna fundamentals, Antenna Fundamentals We shall discuss here only t...
Antenna Fundamentals We shall discuss here only the fundamental concepts needed to understand the role of an antenna as a power-coupling element of a system. Figure illustrates
Instruction size , Instruction size As we have seen already that eac...
Instruction size As we have seen already that each instruction has two parts Opcode ( Operation Code) Which tells the types of operation to be performed .
Develop logic expression and find one possible logic circuit, Q. Figure (a)...
Q. Figure (a) shows the seven-segment array that iswidely used to formthe decimal digits 0 to 9 in LEDdisplays, as indicated in Figure(b). Let the inputs be the four binary digits
logical and with accumulator instruction , ANA Logical AND with Accumula...
ANA Logical AND with Accumulator Instruction This instruction is used to logically AND the accumulator of any register or memory location with the accumulator and the r
Biasing clamper, Ask question #Minwhat is biasing of clamper imum 100 words...
Ask question #Minwhat is biasing of clamper imum 100 words accepted#
Explain the working of direct memory access controller, Explain the various...
Explain the various modes in which DMAC works. Working of Direct memory access controller: The modes of operation has demand mode, block mode, single mode and cascade mode.
Write a short note on rs-232-c, Write a short note on RS-232-C. The RS-...
Write a short note on RS-232-C. The RS-232 standard is a collection of connection standards among different pieces of equipment. The EIA RS-232 serial communication standard is
Binary coded decimal to decimal conversions, Binary Coded Decimal to Decima...
Binary Coded Decimal to Decimal Conversions • Step1. Break up the Binary Coded Decimal number into 4 bit binary number, starting from the least significant binary bit. • Step2
Accounting Assignment Help
Economics Assignment Help
Finance Assignment Help
Statistics Assignment Help
Physics Assignment Help
Chemistry Assignment Help
Math Assignment Help
Biology Assignment Help
English Assignment Help
Management Assignment Help
Engineering Assignment Help
Programming Assignment Help
Computer Science Assignment Help
IT Courses and Help
Why Us ?
~24x7 hrs Support
~Quality of Work
~Time on Delivery
~Privacy of Work
Human Resource Management
Literature Review Writing Help
Follow Us |
T & C
Copyright by ExpertsMind IT Educational Pvt. Ltd.