Layout of vessels in plant design, Mechanical Engineering

Assignment Help:

Q. Layout of vessels in plant design?

Layout of vessels needs to allow sufficient spacing for instruments, piping, operations, maintenance and firefighting access.

Vessels operating above 316 °C (600 °F) or above auto-ignition temperature represent an increase risk of fire. Equipment located above vessels containing hydrocarbons operating above 316°C (600°F) or above auto-ignition temperature (whichever is lower) should be protected by measures such as passive fire protection or water sprays.

Internally insulated vessels are more vulnerable to overheating and potential failure when exposed to external fires, so increased spacing is justified.

For very large vessels, consider providing a toe-wall around the vessel a minimum of 3 m (10 ft.) from the vessel shell. No other equipment should be installed within the toe-wall. Toe-wall contained areas shall be adequately drained to prevent hydrocarbon pool fires occurring in the event of major spills. For large multi-level structures, such toe-wall containment and drainage shall be designed to prevent escalation offire to lower levels by burning hydrocarbon fluids. If possible, locate vessels with the largest inventory of fluids at the bottom of the structure to permit faster drainage and fire fighting access. Blowdown and water disengaging drums should be located in a separate unit area to avoid involvement in process unit fires.

Large vessels should be located close to battery limits to allow easy access of mobile lifting equipment. Vessels containing catalyst, resins, filters, cartridges or packing require space for bins or pallets and lifting facilities for filling / emptying of materials. Where a series of beds are involved, access to each bed will be required. Reactors have a substantial top platform with lifting facilities for removal of reactor head and catalyst loading. Reactors can have platforms attached or have an independent access structure.

Towers and columns shall be located in a way that all working platforms and manholes face the access road. Manways shall be on or about a common centerline.

Where vessels are fitted with agitators, lifting facilities shall be provided for motor / agitator blades removal and set down. This can affect building heights. If a travelling crane is used, motor / agitator travel routes should not pass over other equipment.

Permanent access should be provided to manholes and instrumentation on all vessels. Access to platforms from ladders should be by side stepping wherever possible.


Related Discussions:- Layout of vessels in plant design

Mechanotechnics, list 5 important factors in the design of a workshops layo...

list 5 important factors in the design of a workshops layout

What is ifd in project management, Q. What is IFD in project management? ...

Q. What is IFD in project management? The P&IDs now reflect the next intermediate stage of development and incorporate any changes requested by the Customer during the IFA revi

Illustrate the future trends in automobile, Short answer Type. a) Writ...

Short answer Type. a) Write the difference Between Dry clutch and Wet ? b) What is difference Between Chasis and Frame? c) Illustrate the Future trends in Automobile

Submerged arc welding - set up, SUBMERGED ARC WELDING-Set Up Submerged ar...

SUBMERGED ARC WELDING-Set Up Submerged arc welding system consists of the following basic modules: 1. Welding head 2. Power source 3. Flux feeding and recovery units Schematic

Manufacturing technology, with the aid of a diagram explain electrochemical...

with the aid of a diagram explain electrochemical grinding

The many uses of iron, 5000 word assignment 25/10/2018 due date Research P...

5000 word assignment 25/10/2018 due date Research Project for ENGR8752 Engineering Physics and Material write down about the iron history and all about iron my detail yesh patel

What do you understand by straight line mechanism, What do you understand b...

What do you understand by straight line mechanism ? Describe with a neat sketch the working and construction of any three types of straight line mechanism. Derive a mathematical

Gear box, how we can design a shaft for gear box

how we can design a shaft for gear box

Gear boxes , Gear Boxes : Motorcycle engines do not produce their full pow...

Gear Boxes : Motorcycle engines do not produce their full power at all RPM. There is very little power at idle and the power goes up as the engine RPM increases. At a certain RPM,

Dynamic machine routing, Dynamic Machine Routing  Machine routing ident...

Dynamic Machine Routing  Machine routing identifies the machines that are needed for each of the operation of a given job. Within the JSP or Job Shop Scheduling Problem model,

Write Your Message!

Captcha
Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd