Write out the swing equations for the pre-fault

Assignment Help Electrical Engineering
Reference no: EM132185045

Project Assignment -

The assignment is about the stability in power system (Electrical Engineering). You need to answer this project by using Matlab. You cannot use any Matlab code written by anyone else and you need to write the Matlab code for the project yourself.

Problem: Consider the classical power system discussed in the lectures where one generator is connected to the infinite bus through two transmission lines. We want to study the transient stability for a fault on one of the two lines. The generator parameters are as follows: Pm = 1, H = 4, KD = 5, x'd = 0.25, E' = 1.4. The transmission line where the fault occurs has a line reactance of 0.6 pu. The other transmission line that remains in service has a line reactance of 0.75 pu.

a) Suppose the fault occurs at the middle of the line. Write out the swing equations for the pre-fault, fault-on and post-fault systems.

b) Suppose the clearing time is stated as 6 cycles. Use the Euler algorithm with a step size of one millisecond to compute the trajectory during the fault-on period and compute the clearing state. Carry out the Euler algorithm for 20 seconds into the post-fault period assuming an integration step size of one millisecond. Is the system transient stable or not?

c) Repeat Part b) after changing the fault clearing time to be 7 cycles. Is the system transient stable? Repeat the study by increasing the clearing time in steps of one cycle. The largest value of the clearing time when the system is still transient stable is known as the critical clearing time. Keep repeating the simulation while increasing the clearing time by one cycle at a time till the system becomes transient unstable. What is the critical clearing time?

d) Repeat Parts b) and c) for a fault that is located very close to the generator bus. Discuss your results.

e) Apply the equal area criterion to check for the transient stability of the system for part (a) the instantaneous clearing case.

Attachment:- Assignment Files.rar

Reference no: EM132185045

Determine the contact resistor that can go on the base

(a) determine the contact resistor that can go on the base if the length of the contact is 10 * Wb. (b) Plot the change in conductance in relation to varying the doping from

Find and plot straight-line approximations to the amplitude

a) Find and plot the straight-line approximations to the amplitude and phase response bode plots b) sketch the approximate amplitude-response bode plot od this system using

What would be the degree and the values of coefficients

Inverse Z-transform and poles and zeros. When finding the inverse Z-transform of functions with z-1 terms in the numerator, the fact that z-1 can be thought of as a delay op

What is the gain of an ideal amplifier connected to drive

A power amplifier employs an output stage whose gain varies from 2 to 12 for various reasons. What is the gain of an ideal (non varying) amplifier connected to drive It so t

Find the maximum acceptable propagation loss for the system

The speech quality for a particular mobile communication system is just acceptable when the received power at the terminals of the mobile receiver is -104 dBm. Find the maxi

Calculate the bandwidth of the closed-loop transfer function

In a feedback system, the forward path has a transfer function of the form G(s)=k/(1+s/Omega_p) and the feedback path has a gain of k_fb which is less than unity. Calculate

Derive expressions for the amplitude and frequency of the ac

where i is the current at time t, and k is a constant. Assuming that optical losses are negligible for the arrangement, derive expressions for the amplitude and frequency of

Determine the conduction parameter and the threshold voltage

Consider a GaAs MESFET. When the device is biased in the saturation region, we find that Id = 18.5µa and Vgs=.35 V and Id=86.2µa at Vgs=.5V. Determine the conduction paramet

Reviews

len2185045

12/4/2018 12:32:59 AM

The assignment is about the stability in power system ((Electrical Engineering)). You need to answer this project by using Matlab. You cannot use any Matlab code written by anyone else and you need to write the Matlab code for the project yourself. I upload one sample of an old project, you can take look on it. DON'T COPY FROM THE SAMPLE.

len2185045

12/4/2018 12:32:53 AM

Rules: No discussion of any sort with any other student. You cannot use previous year solutions or solutions from other students. You cannot use any Matlab code written by anyone else. You need to write the Matlab code for the project yourself. In case of questions, please see the instructor. If the rules are not followed in the take home exam, that will lead to a Fail grade in the course.

Write a Review

 
Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd