Why are leads used when driving piles

Assignment Help Mechanical Engineering
Reference no: EM131233748

1. Investigate on the Web the advantages and disadvantages of using a double-acting hammer (air or steam) to drive piles.

2. Why are leads used when driving piles?

3. A Vulcan model 016 single-acting hammer is used to drive a pile. The stroke of this hammer is 36 in. The average penetration per blow for the last 10 blows is i in., what will be the safe rated load using the Engineering News equation?

Reference no: EM131233748

Questions Cloud

Describe the main function of a pile foundation : Describe the main function of a pile foundation. - Piles are made out of different materials. List the major advantages and disadvantages of prestressed concrete piles.
Maximize objective function : A linear program is defined as follows: Maximize Objective Function (4X1 + 2X2); subject to constraints: X1 ≥ 4; X2 ≤ 2; X1 ≥ 3; X2≥ 0; which of the following statements is true about this linear program?
Find the specific reversible work for a steam turbine : A steam turbine receives steam at 6 MPa, 800?C. It has a heat loss of 49.7 kJ/kg and an isentropic efficiency of 90%. For an exit pressure of 15 kPa and surroundings at 20?C, find the actual work and the reversible work between the inlet and the e..
Amount of mustard dispensed from a machine : The amount of mustard dispensed from a machine at The Hotdog Emporium is normally distributed with a mean of 0.9g and a standard deviation of 0.1g. If the machine is used 500 times, approximately how many times will it be expected to dispense 1 or ..
Why are leads used when driving piles : Investigate on the Web the advantages and disadvantages of using a double-acting hammer (air or steam) to drive piles. - Why are leads used when driving piles?
Define corporate culture : State the specific outcomes and metrics for the organization change ? Define corporate culture? Why do conflicts often exist in organizations wherein everyone ostensibly works toward the same common goal? Are company subcultures a factor in such conf..
Calculate the reversible work out of the two-stage turbine : Calculate the reversible work out of the two-stage turbine shown in Problem 4.86, assuming the ambient is at 25?C. Compare this to the actual work, which was found to be 18.08 MW.
Determine the volume of air after it is compressed : The air is compressed to a gauge pressure of 100 psi at a temperature of 140°F. The atmospheric pressure is 14.0 psi. Determine the volume of air after it is compressed.
Real zero between two given numbers : How do you show that a polynomial function has a real zero between two given numbers? Give an example to support your answer.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Amagots law and the generalized compressibility chart

A rigid tank contains 2 kmol of N2 and 6 kmol of CH4 gases at 200 K and 12 MPa. Estimate the volume of the tank using Amagot’s Law and the generalized compressibility chart

  Calculate rate of heat loss per foot and thermal resistance

Calculate the rate of heat loss per foot and the thermal resistance for a 6-in. schedule 40 steel pipe covered with a 3-in. thick layer of 85% magnesia. Superheated steam at 300°F flows inside the pipe (hc = 30 Btu/h ft2 °F) and still air at 60°F is ..

  Describe the simplest heat treatment procedure

Briefly describe the simplest heat treatment procedure that would be used in converting a 0.76 wt% C steel from one microstructure to the other

  The pistons of a v6 automobile develops 225hp if the

the pistons of a v6 automobile develops 225hp. if the engine drive shaft rotational speed is 4700 rpm and the torque is

  Determine the fan power input needed to overcome

determine the outlet temperature of air as it leaves the underwater portion of the duct. Also, for an overall fanefficiency of 55 percent, determine the fan power input needed to overcome the flow resistance in this section of the duct.

  Combustion process taking place in a sealed container

In a combustion process taking place in a sealed container, 160kg of methane is burned in 560kg of O2 and 1845kg of N2 to yield CO, CO2, H2O and N2 as the products of combustion. How many kg of CO are produced?

  Determine which dislocation segment moves

An L shaped edge dislocation ABC in a crystal is shown in Figure below. The stresses acting on the crystal are also shown. Determine which dislocation segment moves and which dislocation segment does not move. What will be the shape of the crystal..

  An insulated vertical piston-cylinder device initially

an insulated vertical piston-cylinder device initially contains 10kg of water 6kg of which is in the vapor phase. the

  Determine the net power developed by the plant in kw if the

in a gas turbine operating at steady state air enters the compressor with a mass flow rate of 5 kgs at 0.95 bar and

  What is the speed of shaft b

Suppose that the motor is spinning shaft A at a speed of 1800 rpm. State all speeds in units of rpm. What is the speed of shaft B. What is the speed of shall C. What is the speed of shaft D?

  What rms velocity will the drill have

What natural frequency must a hand drill have if its vibration must be limited to a minimum rms displacement of 10 μm and rms acceleration of 0.1 m/s2 ? What rms velocity will the drill have?

  The distance from the top surface of the beam to the

a cantilever beam ab is loaded by a couple m0 at its free end see gure. the length of the beam is l 20m and the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd