What would be the salt concentration be in the brine

Assignment Help Civil Engineering
Reference no: EM13549183

1.The motion of the 2.5-kg rod AB is guided by two small wheels which roll freely in horizontal slots. If a force P of magnitude 8 N is applied at B, determine (a) the acceleration of the rod, (b) the reaction at A and B.

2.A reverse osmosis plant desalinates 5*10^6 L/day of feedwater containing 1500 mg/l of salt, yeilding 3*10^6L/day of product water with 75 mg/l of salt. What would be the salt concentration be in the brine?

3.A pole is held vertically on a soil surface by three equally spaced wires tied to the top of the pole. each wire has a tension of 1kN and is inclined at 45 degree to the vertical. calculate the increase in vertical stress at a depth 1 m below the surface and the amount of elastic settlement below the axis of the pole if E = 40 Mpa and v=0.45

Reference no: EM13549183

Questions Cloud

What must the hydraulic detention time be in the aeration : A perfectly mixed aeration pond with no recycle (return line) serves as the biological reactor for a small community. The pond receives 30 cubic meters/day of influent with a BOD5 of 350 mg/L that must be reduced to 20 mg/L before discharge.
Define sea level to the top of the atmosphere : Sea-level atmospheric pressure is approximately 14.7 pounds per square inch. From this fact, we can deduce that a column of air one square inch in cross-section, measured from sea level to the top of the atmosphere
Find the deflection at the free end caused by the beams own : A cantilevered W12X136 (ASTM-A36) steel member beam is 18 feet in length. if a concentrated load of 12 kips is applied at a point 6.25 feet from the beam's free end, use the superposition technique to find
Explain what mass of oxygen would be required to convert : A sample of 13 g of nitrogen can be combined with 14.857143 g of oxygen to form nitric oxide gas (NO). What mass of oxygen would be required to convert the same sample of nitrogen to nitrogen dioxide (NO2) instead
What would be the salt concentration be in the brine : A reverse osmosis plant desalinates 5*10^6 L/day of feedwater containing 1500 mg/l of salt, yeilding 3*10^6L/day of product water with 75 mg/l of salt. What would be the salt concentration be in the brine?
Find the mass of water that has been frozen into ice : A 0.250-kg piece of aluminum that has a temperature of -158 °C is added to 1.4 kg of water that has a temperature of 2.6 °C. find the mass of water that has been frozen into ice
Explain hydrogen-like atom in the ground-state : If a hydrogen-like atom in the ground-state is excited with a wavelength of 397.21nm, how much energy has been absorbed. Which shell is the electron excited to
Evaluate the moment of inertia of the top : A string wrapped around a peg (diameter=2.00 cm) along the axis of a top is pulled with a constant tension of 5.92 N. what is the moment of inertia of the top
Define what volume of glacial aceic acid is required : What volume of glacial aceic acid (18M) and what weight of sodium acetate trihyddrate(CH3COONa.3H20) are required to make 100 ml of .2 M buffer at pH 4.5 (pKa of acetic acid is 4.74). please explain steps in detail and use units in asnwer

Reviews

Write a Review

 

Civil Engineering Questions & Answers

  Design the weir structure in order to accommodate the design

The channel cross section is rectangular in shape,with a bed width of 4 m and Manning n of 0.022. The bed drops by an average of 4.2metres every kilometre. The maximum flow in the channel is equal to 7 m3/s.

  Determine the maximum possible mass flow rate of air

Assume that the upstream pressure is 60 psi and that the flow is isothermal at 68F, determine the maximum possible mass flow rate of air for which the assumption of incompressible flow is a vaild engineering approximation.

  Determine the bubble point pressure for a mixture

For a mixture 10 mol % methane 20 mol % ethane 70 mol % butane at 50 degrees Fairenheit determine the bubble point pressure

  Determine density on the highway and flow on the road

Data obtained from aerial photography showed six vehicles on 900 ft-long section of road. Traffic data collected at the same time indicated an average time headway of 4.3 sec. Determine (a) The density on the highway. (b) The flow on the road, and

  Find the correction for the calibration of the measuring tap

Find the correction for the calibration of the measuring tape using its formula. During the calibration of the measuring tape on comparator of 100.000m the length of the tape turned out to be of 99.993m

  Determine what are the discharge and the flow veloctiy

An 18in. diameter sewer is placed on a grade of 1.5ft/1000ft. What are the discharge and the flow veloctiy when the pipe is full

  What other structural considerations are necessary in the

If the maximum allowable compressive stress of timber is 7MPa, what is the minimum available size of square section post required. (give dimensions as well as area). Please show working.

  Make necessary calculations to select the pit from

A proposed embankment fill requires 8000 cubic meters of compacted soil. The void ratio of the compacted fill is specified as 0.7. Four borrow pits are available along with each of the respective void ratios along with the cost per cubic meter for mo..

  Determine the maximum external pull the ferrari has

A ferrari with 808 hp has a max. speed of 211 mph at 6,300 rpm. the Ferrari weighs 4,155 lb/ton and is operated over a smooth concrete road with a rolling resistance of 40 lb/ton and a slope of 3%.

  Determine the rate of heat transfer to the stock in furnace

Cylindrical, steel bar stock (density = 7833 kg/m3, Cp = 0.465 kJ/(kg C)) of 10-cm diameter is heat-treated by drawing it at a velocity of 3 m/min through a 6-m-long furnace maintained at 900C.

  Determine the increment of vertical stress at all points

Constructing the foundation causes changes in the levels of vertical stress at all points in the soil. One such point lies at the centre of the footing plan and is at a depth of 10m. Determine the increment of vertical stress there.

  Compute the true static height in a glass tube

Pure water at 50 degrees Fahreneit stands in a glass tube of 0.04-in diameter at a height of 6.78 in. Compute the true static height.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd