What will be the frequency of the motion in hertz

Assignment Help Mechanical Engineering
Reference no: EM13980831

2-kg of potatoes are put on a spring scale that is displaced 2.50 cm as a result. If the scale is pushed down 2 cm from the equilibrium position and allowed to oscillate, what will be the frequency of the motion in Hertz?

Reference no: EM13980831

Questions Cloud

Change of the balance sheet : At the end of a fiscal year, a company makes a net profit of $100 and does not pay a dividend. Which of the following is a possible change of the balance sheet?
What survey objectives would act : What survey objectives would ACT have in asking colleges how they use its essay test? What objectives would Kaplan have for its survey research?
How many revolutions does the disk make before it stops : Starting with an agular velocity of 13.90 rev/s, the disk is subjected to a constant torque of 3.0 Nm until it stops. How many revolutions does the disk make before it stops?
Appropriate discount rate-what is the present value : An investment will pay you $33,000 in 12 years. If the appropriate discount rate is 6 percent compounded daily, what is the present value?
What will be the frequency of the motion in hertz : 2-kg of potatoes are put on a spring scale that is displaced 2.50 cm as a result. If the scale is pushed down 2 cm from the equilibrium position and allowed to oscillate, what will be the frequency of the motion in Hertz?
Global trade can bring highly advanced technologies : Global trade can stimulate economic growth and alleviate poverty.
Place of employment : Using your local business, organization, or place of employment, discuss your experience as a group member or group leader seeking to solve a problem in your organization.
Write a short presentation on a drainage project : Write a short presentation on a Drainage project, How you will do it , what program you will use.
What annual discount rate will make the project : You receive $10,000 that obligates you to provide an event that will cost $11,000. Assuming the event is held one year from today, what annual discount rate will make the project have a net present value greater than zero? 8, 9, 10, or 11%? The answe..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  If the pot is initially full of saturated water at 200 kpa

a six liter 6 l pot is fitted with a heavy lid that allows a maximum of 200 kpa of absolute pressure. heat is added to

  Time grain diameter min mm 21 00592 97 00823 a what was the

the average grain diameter for some metal alloy was measured as function of time at 650degc which is tabulated below at

  Perspective on the project team experience

Write a short essay describing your personal perspective on the project team experience so far. To the extent possible, please comment on the following:

  Describe one method for manipulation of microstructure and

describe one method for manipulation of microstructure and mechanical properties for each of the following class of

  The sphere is cooled by 20oc air with a convection heat

a 20 cm diameter sphere is made of a heat-generating material that produces 106 wm3. the sphere is cooled by 20oc air

  Water is heated until the tank contains only saturated vapor

A closed, rigid tank is filled with water. Initially, the tank holds 9.9 ft^3 saturated vapor and 0.1 ft^3 saturated liquid, each at 212F. The water is heated until the tank contains only saturated vapor.

  Energy when completely combusted in air

As a 75 slug car travels along a horizontal, 3200 ft section of road, it changes speed from 5 mph to 60 mph. During this acceleration, the car gets an average MPG of 15 MPG. How efficient is the car’s engine during the acceleration assuming 1 gallon ..

  Square cross section of edge length

A bar specimen having a square cross section of edge length c is subjected to a uniaxial tensile force F, as shown in the fol- lowing figure. Derive strength and stiffness performance index expressions analogous to Equations 22.9 and 22.11 for thi..

  A single metallic crystal is oriented such that the normal

a single metallic crystal is oriented such that the normal to the slip plane and slip directions are at angles of 50

  Estimate the tensile strength of the wire and the work

estimate the tensile strength of the wire and the work required to take 1m3 of the wire to the point of necking. the

  This nuclide is produced by the endoergic reaction 16onp16n

an important radionuclide produced in water-cooled nuclear reactors is 16n which has a half-life of 7.13 s and emits

  The rod must stretch less than 0125 mm determine an

an engineer determines that a 40 cm long rod of 1020 grade steel will be subjected to a tension of 20 kn. the following

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd