What time will be required at 500degc to produce the same

Assignment Help Mechanical Engineering
Reference no: EM13609417

The wear resistance of a steel shaft is to be improved by nitrogen hardening of its surface. The initial nitrogen content of steel is 0.002wt%, whereas the surface concentration during heat treatment is maintained at 0.50wt%. A nitrogen content of 0.1wt% is desired at a position of 0.40-mm below the surface a.) Determine the diffusion time required at 600°C. The pre-exponential and activation energy for diffusion of nitrogen in steel is given as 3X10^-7 m²/s and 76.15KJ/mol, respectively. b.) What time will be required at 500°C to produce the same resul (in terms of concentration at a specific depth) as for 10-hours at 600°C?

Reference no: EM13609417

Questions Cloud

Suppose we draw two tickets from a hat that contains : suppose we draw two tickets from a hat that contains tickets numbered 1234. let x be the 1st number drawn and y be the
A short squared timber post supports a load of 115000 : a short squared timber post supports a load of 115000 pounds. if the allowable unit compressive stress is 1000 psi what
A rock is dropped into a deep hole and 25 s later the : a rock is dropped into a deep hole and 2.5 s later the sound of striking the bottom is heard. if the speed of sound is
The alphonse company allocates fixed overhead costs by : the alphonse company allocates fixed overhead costs by machine hours and variable overhead costs by direct labor hours.
What time will be required at 500degc to produce the same : the wear resistance of a steel shaft is to be improved by nitrogen hardening of its surface. the initial nitrogen
A flat sheet of paper of area 0200 m2 is oriented so that : a flat sheet of paper of area 0.200 m2 is oriented so that the normal to the sheet is at an angle of 80deg to a uniform
High quality standards in an international enviroment : high quality standards in an international enviroment include which of the following. a they permit a wide variety of
When a company is experiencing rapid growth which of the : when a company is experiencing rapid growth which of the following statements is the most correct? cash flow from
Sabranes-oxley regulations have given the securites and : sabranes-oxley regulations have given the securites and exchange commission new powers. list these guidelines and

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A valve connected to the cylinder is now opened and air is

a vertical piston-cylinder device initially contains 0.25 m3 of air at 600 kpa andnbsp300degc. a valve connected to the

  A mummy picks up a calculator and starts adding odd whole

a mummy picks up a calculator and starts adding odd whole numbers together in order 135....etc. what will be the last

  Initially the air in this tank is at 20 psia and 70 degrees

a scuba divers 2 cubic foot air tank is to be filled with air from a compressed air line at 120 psia and 100 degrees f.

  Determine the power of a pump if 2000 kgmin of water is

determine the power of a pump if 2000 kgmin of water is compressed from 100 kpa to 1 mpa. the water density can be

  Determine the compression of each spring when the car is

the train car has a mass of 10 mg and is traveling at 5 ms when it reaches a. if the rolling resistance is 1100 of the

  Te point starts moving at t0 find the total distance

the position of a point p on a line is given by the equation x t sinpi t2. the point starts moving at t0. find the

  Write a report about heat treatment of steel

How transformations affect the microstructure and mechanical properties of steel.

  Determine the efficiency and the horsepower output if the

a four-stroke-cycle engine operates on the air-standard diesel cycle. the engine has six cylinders with a 0.105 m bore

  Determine the maximum shear stress

Draw the Mohr's circle for this stress state, deterrnine the principal stresses and the angle of the principal direction to the x-axis and determine the maximum shear stress.

  The vessel volume is 15m3 and a standard six-blade open

an agitation system is to be designed for a fluid having a density of 950kgm3 and viscosity of 0.005pas. the vessel

  Develop an algebraic expression in the form of an integral

a cross section of a rotating bearing is shown. the spherical member rotates with angular speed omega a small distance

  If the reading on the pressure gage is 80 kpa determine the

both a gage and a manometer are attached to a gas tank to measure its pressure. if the reading on the pressure gage is

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd