User Account

All Pages

What should be the diameter of the bottom of the sprue

Assignment Help Mechanical Engineering
Reference no: EM13710467

A sprue is 12 inches long and has a diameter of 5 inches at the top, where the metal is poured. The molten metal level in the pouring basin is taken as 3 inches from the top of the sprue for design purposes. If a flow rate of 40 in3/s is to be achieved, what should be the diameter of the bottom of the sprue? Will the sprue aspirate? Explain.

Reference no: EM13710467

Questions Cloud

What percentage theoretical air must be used : Gaseous propane at 77  oF is mixed with air at 300oF and ignited. What percentage theoretical air must be used if the temperature of the products is 1700oF? Assume an adiabatic process.
Find what work does he do on the wagon : Your little cousin pulls a red wagon along the sidewalk a distance 12.5 m. What work does he do on the wagon
Determine the electric field and the electric potential : Two charges -1microC and 2 microC are placed at the corners of an equilateral triangle with side 2m. Determine the electric field and the electric potential
Determine the work done by you : You push your couch a distance of 6.0 m across the living room floor with a horizontal force of 225 N. What is the work done by you, by the friction force, by gravity, and by the net force
What should be the diameter of the bottom of the sprue : A sprue is 12 inches long and has a diameter of 5 inches at the top, where the metal is poured. The molten metal level in the pouring basin is taken as 3 inches from the top of the sprue for design purposes. If a flow rate of 40 in3/s is to be achiev..
What is the kinetic energy of a ball : What is the kinetic energy of a ball of mass 16.1 kg at the apex (highest point) of its trajectory, if it is thrown with an initial speed of 45 mph and an initial angle of 42.8o with respect to the horizontal
Determine the slenderness ratio and column constant : A 10 inch long cantilevered beam has a 1” by 1” square cross section. The load at the end of the beam cycles from 0 lbs to 300 lbs. determine the stress. Determine the slenderness ratio and column constant of a 38” long steel column that has a 1.5 in..
What is the torque exerted on the merry-go-round : A force of 10.0N is applied to a 25.0kg merry-go-round that has a radius of 4.00m. What is the torque exerted on the merry-go-round
What is the heat transfer that must occur to maintain : A 3in diameter can which is 6in tall contains R134a at 70oF. Initially the can is half full, by volume, of liquid R134a. The can is connected to and air conditioning system and is used to fill up that system. Knowing only vapor R134a leaves the conta..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A secondary settling tank is to be designed for a municipal

a secondary settling tank is to be designed for a municipal wastewater treatment facility. the influent tss is 1000 mgl

  The cables direction is 100i - 100j - 100k and it has a

an old wooden telephone pole with a single cross member was blown off center during a recent storm. to temporarily

  What is the probability that there are anywhere from 2 to 4

suppose the past data indicates that the probability of a fluorescent light produced from a production line has a

  Determine the heat transferred in this process

A 10 kg mass undergoes a process. In this process it transfers 2 kJ of work to its surroundings; it increases in elevation by 50 m, and increases its velocity from 15 m/s to 30 m/s. Its specific internal energy decreases by 5 kJ/kg. For this process ..

  Reduces volumetric efficiency at high engine speeds

A four-stroke engine has a total displacement volume of 10L, 125mm bore and 16.3:1 compression ratio. The engine produces a maximum of 210 kW at 2100 RPM. The intake air is at 45 degrees C and 22.5 g/s of air flow into each cylinder. Calculate the vo..

  The a-36 steel axle is made from tubes ab and cd and a

the a-36 steel axle is made from tubes ab and cd and a solid section bc. it is supported on smooth bearings that allow

  What is the satellites altitude

A satellite is in Earth orbit with an altitude at perigee of 555.0 km and an altitude at apogee of 1200.0 km. a. What is the semi-major axis of the orbit? b. What is the eccentricity? c. If the true anomaly is 160 degrees, what is the satellite's ..

  At the beginning of the compression stroke the volume of a

at the beginning of the compression stroke the volume of a certain diesel engine cylin-der is 1.000 liter and it is

  Determine a the natural frequency in rpm of the platform if

a platform of weight 200 lb supported by two springs each of constant k 250 lbin. is subjected to a periodic force of

  A 25 pound block b is moving with a velocity v06 fts as it

a 2.5 pound block b is moving with a velocity v06 fts as it hits a 1.5 pound sphere a which is at rest hanging from a

  The convective heat transfer coefficient between the outer

on a cold winters day it is 30degf outside. yet the temperature of the outside surface of the mechanical engineering

  The lowest temperature that has been achieved is about 1

the lowest temperature that has been achieved is about 1 times 10-6 k. to achieve this an additional stage of cooling

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd