What should be the correct logic levels on a7-a3

Assignment Help Electrical Engineering
Reference no: EM13247949

A given peripheral has 3 address lines (allowing access to 8 internal addresses) and requires that address lines A2-A0 to be used. It is desired that this peripheral occupy the hex address range, EB80-EB87 in a given computer system memory map. What should be the correct logic levels on A7-A3 to permit access to this peripheral.

Reference no: EM13247949

Questions Cloud

What they want from different parts of the same ship : You can usually identify one "top" item that's in both parties lists. If so, that may become their best alternative to reach an integrative negotiation.
Calculate the net flux through each surface : Let all the three charges be placed at the center of a tetrahedron, composed of four triangular faces of equal area. Calculate the net flux through each surface
Calculate the wavelength of the emitted photon : In a scanning electron microscope, an electron is accelerated by a static electrode biased with a 12 kV voltage relative to the electron source. Upon bombarding the sample the electron “kick out†photons with specific wavelength.
What is the gravitational feild and potential : 3 Mass points each of mass m are placed at the vertices of an equilateral triangle of side l. What is the gravitational feild and potential due to 3 masses
What should be the correct logic levels on a7-a3 : A given peripheral has 3 address lines (allowing access to 8 internal addresses) and requires that address lines A2-A0 to be used. It is desired that this peripheral occupy the hex address range, EB80-EB87 in a given computer system memory map.
Find the maximum torque on a square loop of wire : What is the maximum torque on a 125 turn square loop of wire 18.0 cm on a side that carries a 46.0 A current in a 1.60 T field
How are increasingly standardized data : How are increasingly standardized data, access to third-party datasets, cheap, fast computing, and easier-to-use software collectively enabling a new age of decision making?
Calculate hall voltage across the wire : An Aluminum wire with a square cross section 2mm on a side is carrying a current of 1.5amps. Aluminum has a resistivity of 2.69*10^-6 ohm-cm and an atomic volume of 10cc/mol. Assuming aluminum has three free electrons per atom
Determine the electrical force between a two charges : What is the electrical force between a two charges that each has a charge value of .0004 C each that are 2 meters apart

Reviews

Write a Review

 

Electrical Engineering Questions & Answers

  Determine the voltage regulation at rated load

A 75-kVA, 230-V/115-V, 60-Hz was tested with these results: Open-circuit test: 115 V, 16.3 A, 750 W; Short-circuit test: 9.5 V, 326 A, 1200 W a) Determine the voltage regulation at rated load, 0.8 power factor lagging.

  Determine the voltage v across the circuit

A circuit consists of a current source, i=0.030 sin 500t, in parallel with L=20mH, C=50 micro Farads and R=25 Ohms. a. Determine the voltage V across the circuit. b. Solve for the power factor of the circuit.

  Compute the voltage indicated

resistor: a volt-ohmmeter with an internal impedance of 1000 Ω/V and an EVM with an impedance of 11 MΩ. Calculate the voltage indicated by each of these devices.

  Design the circuit to establish a dc emitter current of 1ma

Design the circuit to establish a dc emitter current of 1mA and provide the highest possible voltage gain while allowing for a maximum signal swing at the collector of +-2V. Use +10V and -5V power supplies.

  Develop an approach using the ite-operator

In other words, your approach should be able to answer the question whether two BDDs are complements of each other, without using the complement operation.

  Calculate the traffic load per cell

The system uses a 7-cell reuse pattern. If the offered traffic per user is 0.03 Erlangs and the average number of calls per hour per user is 1.5, for an Erlang-C system with a probability of delaying a call being 5%, calculate the traffic load per..

  What is probability distribution of equivalent construction

a road between fairbanks and nome, alaska, will have a most likely construction cost of $4 million per mile. doubling this cost is considered to have a probability of 30%, and cutting it by 25% is considered to have a probability of 10%.

  Find admittance as appropriate for each branch

A quick description of R5 is needed before the next calculation can be completed. R5 is called a sampling resistor. R5 is put in series with the power supply so it shares the same current as the circuit. This is the TOTAL current

  Determine the value procedures at the primary output

draw a digital design consisting of 2 input AND gates and three inverters, where an inverter is connected to each of the AND gates input and its output. For each of the four possible combinations inputs applied to the two primary inputs.

  To what value should the 2 a source be changed to reduce vx

(a) Using superposition, determine the voltage labeled vx in the circuit represented. (b) To what value should the 2 A source be changed to reduce vx by 10% (c) Verify your answers by performing three dc sweeps in PSpice.

  What precentage of sound energy is reflected

If the accoustic impedance of water is 1.49 and for steel is 42.1, what precentage of sound energy is reflected at a water-to-steel interface? 12.5%,86.8%,43.9% or 43.59%.

  Find the magnetic field at the origin

A semicircular current elment of radius b is positioned in the x-y plane and has its center at the origin. A second long current element is placed along the coordinate y= -b. If current magnitude I flows through each element in clockwise direction..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd