What shear stresses exist at the bottom points

Assignment Help Civil Engineering
Reference no: EM13314187

A rectangular beam of width 300 mm and depth 450 mm supports loads producing a shear force of 300 kN at a particular section. What shear stresses exist at the following points?

a) At mid depth

b) At the bottom

c) 150 mm from the top

Reference no: EM13314187

Questions Cloud

Determine maximum permissible deflection that may be allowed : If this rod is to be used again with an initially straight axis, determine the maximum permissible deflection that may be allowed during testing procedures. Young's Modulus = 210 kN/mm2 and Yield stress of the steel= 240 N/mm2.
Discuss bracing types of buildings with real-life example : Discuss bracing types of buildings with real-life example. Provide photograph or sketch for each type of bracing.
Calculate the compression resistance of 200 uc column : Calculate the compression resistance of 200 UC 59.5 column which is 3.6 m high (between lateral supports). Both ends of the stanchion are held effectively in position but only one is also restrained in direction. Use grade 43 steel
Capstone strategic audit : Capstone Strategic Audit
What shear stresses exist at the bottom points : A rectangular beam of width 300 mm and depth 450 mm supports loads producing a shear force of 300 kN at a particular section. What shear stresses exist at the following points
Evaluate the poh of the solution at 25 °c : A solution of NaOH(aq) contains 8.7 g of NaOH(s) per 100.0 mL of solution. Calculate the pH and the pOH of the solution at 25 °C.
Calculate area of flow-hydraulic radius and wet perimeter : Calculate the area of flow, hydraulic radius, wet perimeter, and top width of a 12-inch diameter pipe that flows at 1/4 of its capacity.
How to calculate the ph and the poh : A solution of NaOH(aq) contains 8.7 g of NaOH(s) per 100.0 mL of solution. Calculate the pH and the pOH of the solution at 25 °C.
Explain eulers theorem : Your boss calls you into his office and he is extremely angry. He was embarrassed at a meeting because he put forward a recommendation that you had made and his idea was shot down by one of the technical geniuses in another department.

Reviews

Write a Review

 

Civil Engineering Questions & Answers

  What is probability that will cross within first four gaps

The traffic on the one-­way main street shown below may be satisfactorily described by a Poisson process with an average rate of arrival of 8 cars per minute. A driver (indicated by the box) on the side street is waiting to cross the main street.

  Calculate the net volume of earthworks needed or available

The following data represents, in square meters, the cross-sectional areas along a short portion of highway. Calculate the net volume of earthworks needed or available over the portion of the highway.

  What types of attacks can still occur

Do the administrators of server systems still have to be concerned about, and take further countermeasures against DoS attacks, if so, what types of attacks can still occur, and what measures can be taken to reduce their impact?

  What force should be applied at the lower edge of the plate

A square plate of uniform thickness has a side length of 25 cm that hangs vertically from hinges at its top edge, When horizontal jet strikes the plate at its center, the plate is deflected and comes to rest at an angle of 30o to the vertical.

  Which route is attractive by using total investment analysis

The state highway department is considering six routes for a new highway. Listed below are the estimated construction costs, maintenance costs, and the user cost associated with each route.

  Explain the rule to solve the moment through the reactions

When using singularity functions, if I have a reactionary moment at a cantilever connection, do I use the right hand rule to solve the moment and determine it's direction through the reactions

  How to draw bending moment diagram

How to draw bending moment diagram for this shape and the value of the moment in critical sections assume that the distributed load (w) KN/M and the concentrated load

  What is the average length of queue

Vehicles arrive at a toll booth with a mean arrival rate of 2 veh/min (the time between arrivals is exponentially distributed). The toll booth operator processes vehicles (collects tolls) at a uniform deterministic rate of one every 20 seconds. Wh..

  Determine the deflection of a simple uniformly loaded

Determine the deflection of a simple uniformly loaded beam by the Ritz method,using first one term, then two terms, adn finally three terms in a sine series. Why does the coefficient of sin2piex/L vanish?

  Find what will speed of the object be in meter per second

total energy (E) of a projectile is the sum of its kinetic and potential energy: E= 1/2 mV^2 +mgz where m is mass of projectile, V is speed, g is gravitational constant and z is height. 5.0 kg object, dropped from rest (V=0 at time t=0)

  Find require diameter of bar according to max stress critera

A bar with a circular cross-sectional area is made of SAE 1045 carbon steel having a yield stress of sY = 1000 MPa. The bar is subjected to a torque T=3.75 kNm and a bending moment M=7 kNm. Using a factor of safety FS=2 with respect to yielding

  What was the ph of the soft drink before bottle was opened

You open a 16 oz (1 pint) bottle of a carbonated soft drink that has a temperature of 5°C, then you get distracted and forget to drink it. You come back quite some time later and find that it has gone "flat," and that it has gotten warm (20°C).

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd