What rate of perspiration would be needed to maintain a

Assignment Help Civil Engineering
Reference no: EM13542299

Considere a person who consumes 2100 kcal par day, of which 2000 kcal is converted thermal energy.( the remaining 100 kcal is used to do work on the environment.) The person has a surface area of 1.8 m² and is dressed in a bathing suit.

a) The person is in room at 20°C, with a convection heat transfer coefficient of 3 W/m².K. At this air temperature, the person's average skin temperature.

B) If the temperature of the environment were 33°C, what rate of perspiration would be needed to maintain a comfortable skin temperature of 33°C

Reference no: EM13542299

Questions Cloud

Calculate the linear density of atoms in these directions : For FCC diamond cubic structures, give the lattice coordinates for the atoms found in the [100], [110], [111] direction? and Calculate the linear density of atoms in these directions for Ge.
Determine the correct horizontal distance considering : A civil engineer used a 30-m tape in measuring an inclined distance. The measured length on the slope was recorded to be 459.20 m long. The difference in elevation between the initial and the end point was found to be 1.25 m
Draw the influence line for the shear at point b : Draw the influence line for the shear at point B. Plot numerical values every 5 ft. Assume the support at A is a roller and C is fixed. EI is constant.
Determine the shear force and bending moment diagrams : A wood mallet has a cylindrical head 6 inches long and 3 inches in diameter. If the cylindrical head is 1 inch in diameter how long must it be for the mallet to balance at a point 6 inches from where the handle enters the mallet? (use 40 lb / ft cube..
What rate of perspiration would be needed to maintain a : Considere a person who consumes 2100 kcal par day, of which 2000 kcal is converted thermal energy.( the remaining 100 kcal is used to do work on the environment.) The person has a surface area of 1.8 m² and is dressed in a bathing suit.
Should the company proceed with the process change : The company Eco-Safe is adding pollution control equipment to its process and reducing emission of pollutants. The annual waste disposal cost of the current process is $130,000 and the annual operating cost is $600,000
Determine the viscosity of the fluid : Two parallel plates are separate at a distance of 2mm by a fluid. If a shearing stress of 150 Pa is developed at the upper plate when it is pulled at a velocity of 1m/s. Determine the viscosity of the fluid.
The sydney transportation company operates : The sydney transportation company operates an urban bus systemin new south wales australia. economicanalysis performed by the firm indicates that two major factors influence the demand for its services
Broadly state the objectives of monetary policy : Broadly state the objectives of monetary policy as set by the US Federal Reserve? How different are the Feds policy in this regards from those of the Bank of Canada?

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine what is the volume of the lake in cubic feet

Nitrification, the conversion of ammonia to nitrate (NH3 -> NO3-) occurs in the lake according to first - order kinetics. One stream feeds the lake and one stream empties the lake with the flow rate in both being 8 cfs

  What is expected behavior in charpy impact energy testing

Two identical alloy specimens are being evaluated for use in a new fuel rod design. One sample was exposed to a fast neutron flux of 9 X 10^23 neutrons/(cm2*sec) at a temperature of 323°K for six weeks in a test reactor.

  Find the initial velocity of the bullet before hit the tree

A 9 gram bullet is fired horizontally at a tree and is brought to a halt right before it exits the tree. the tree is 90cm thick and exerts a resistive force of 16000N on the bullet as it travels through the tree

  Determine the adequacy of the design using basic principles

For the eccentric shear loading of the accompanying figure, 7/8 inch diameter A325 bolts are used in two vertical lines in a bearing-type (A325-X) connection. The loading is 10 kips dead load and 30 kips live load.

  Falling-head permeability test

A falling-head permeability test was carried out on a clay soil of diameter 100 mm and length 150 mm. In 4 minutes the head in the standpipe of diameter 5mm dropped from 680 to 350 mm.

  Determine the speed for the free flow speed of a highway

a section of highway has a speed flow relationship of the form q= au^2 + bu it is known that at capacity ( which is 3100 veh/h) the space-menu speed of traffic is 28 mi/h. determine the speed when the flow is 1500 veh/h and the free flow speed.

  How many hours will it take approx to complete the job

a job requires excavating and hauling 500 cyds (in situ) of sandy soil. in your posession is an excavator and a dump truck (capacity 30 cyds loose) the dump truck has a round trip travel time of 5 mins and 45 secs to the dump site and back.

  A vertical curve is formed when a rural highway passes

a vertical curve is formed when a rural highway passes under a bridge joining a -8 grade to the horizontal grade

  What force must be applied at each connection

A concentrated downward force of 2000 lb. is located 6' from the left support, and a uniformly distributed load of 200 lbs./lin. ft. begins 6' to the right end of the member. What force must be applied at each connection to maintain equilibrium?

  Parabolic trajectory of the falling prey

A hawk flying at 2 m/s at an altitude of 45 m accidentally drops its prey. The parabolic trajectory of the falling prey is described by the equation below until it hits the ground, where y is its height above the ground and x is its horizontal dis..

  How far does a horizontal plane depart from a level surface

The width of a lake is 16 km (it is a flat plane tangent to the radius of the sphere). How far does a horizontal plane depart from a level surface if the earth is a sphere with r=6371km

  At what rate must heat be supplied to engine of power

A completely reversible heat engine operates with a source at 1500 R and a sink at 500 R. At what rate must heat be supplied to this engine, in Btu/h, for it to produce 5 hp of power

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd