Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
A manufacturer specification sheet lists the transfer function of a pressure sensor as 45±5% mV/kPa with a time constant of 4±10%. A highly accurate test system applies a step change of pressure from 20 kPa to 100 kPa.
a. What is the range of the sensor voltage outputs initially and finally?
b. What range of voltages would be expected to be measured 2 sec after the step change is applied?
Two LTIC systems have impulse response functions given by h1(t)=(1-t)[u)t)-u(t-1)] and h2(t)=t[u(t+2)-u(t-2)].a) Carefully sketch the functions h1(t) and h2(t). b) Assume that the two systems are connected in parallel.
The configuration is shown in Figure 6.5. Use six LEDs as shown in Table 6.1 to represent the outputs. The Time in This State can be met in several ways. One method is to use a debounced switch as input, another to input a 1 Hz clock.
Interface binary Input Output devices to the microcontroller
Given a 1-phase 50 kVA 12.47 kV pf = 0.8 lagging static load a. Modeling the load as constant complex power, determine the correct value for S and I. b. Modeling the load as constant complex impedance, determine the correct value for Z and I.
1. Point charges Q1 and Q2 are respectively, located at(4,0,-3) AND (2,0,1). If Q2=4nC, find Q1 such that a. E at (5,0,6) has no no z component b. The force on a test charge at (5,0,6) has no x component
If R1 = 220 k Ohms , R2 = 56 k Ohms, Rc = 6.8 k Ohms, RE = 2.2 k Ohms, B= 180, rO = 50 k Ohms, C1 = C2 = 10 uF, CE = 100 uF, and Vcc = 20 V, determine the voltage gain AV.
An uncharged capacitor and resistor are connected in series with a 12V source and switch. What is the voltage across the capacitor after the switch is closed and the capacitor is fully charged
Consider a 4 input, 1 output digital system (W,X,Y,Z, and f respectively) . Design a POS circuit with any number of inputs such that f(W,X,Y,Z) = M(0,2,4,9,13) + D(6,14).
A link is transmitting 10 Mbps in a bandwidth of 10 MHz using 1 mW of power. (Box 1) What change will you do to double the data rate and why (Box 2) How can you use the link if the noise were larger than the signal
Analyze the synchrounous circuit with input X and output Z constructed with two flip flop of JK type with outputs QA and QB. The flip flop input exciatation are as follows: JA=XQB; KA=0; Jb=XQA'; KB=QA. the output equation is Z=XQB'.
A bowling ball is placed on a coil spring. The spring constant is 400N/m. When the bowling ball is placed on the spring, the spring compresses down 0.1m. If the spring is vertical how far will the bowling ball go
Assume that we try to predict this sequence with a BHT using one-bit counters. The counters in the BHT are initialized to the N state. Which of the branches in this sequence would be mis-predicted?
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd