What power does it absorb from the 210-v source

Assignment Help Electrical Engineering
Reference no: EM13285280

An electric heater is connected to a constant 240-V source and absorbs 1000 W. Subsequently, this heater is connected to a constant 210-V source.

(a) What is the resistance of the heater?

(b)What power does it absorb from the 210-V source?

Reference no: EM13285280

Questions Cloud

How to select suitable values for the amplifier parameters : A Transconductance amplifier is to be used to interface a voltage signal Vs(t) to a resistive load R(L)=5k ohms. The signal source is represented by a Thevenin equivalent circuit with a source resistance R(S)=20k ohms.
Estimate the direction of the net force : Two point charges are located on the axis as follows: charge = -1.80 at = -0.500 , and charge = 2.20 at the origin (= 0). What is the direction of the net force
Major tax structures : Major Tax Structures
State the balloon ascends to an altitude : The balloon ascends to an altitude of 20 km, where the pressure is 76.0mmHg and the temperature is -50 degrees C. What is the new volume, V2, of the balloon in liters, assuming it doesn't break or leak
What power does it absorb from the 210-v source : An electric heater is connected to a constant 240-V source and absorbs 1000 W. Subsequently, this heater is connected to a constant 210-V source. (a) What is the resistance of the heater
Calculate the spacing between the plates : When a potential difference of 221 V is applied to two plates of a parallel-plate capacitor, the inner surface of the positive plate carries a surface charge density of 40 nC/cm2. What is the spacing between the plates
Egg of the fruit fly drosophila melanogaster : In the early stages of development in the egg of the fruit fly Drosophila melanogaster, it takes a cell about 5 minutes to replicate the entire genome, which is approximately 1.6 x 10^8 bp long. If DNA in these cells is synthesized at a rate of 30 bp..
Find the power being absorbed by the resistor : A current source of 12 cos2000t A, a 200 ohm resistor, and a 0.2 H inductor are in parallel. Assume steady-state condition exist. At t=1ms, find the power being absorbed by the (a) resistor; (b) inductor; (c) sinusoidal source.
Under what circumstances does the price of the call : A trader buys a European call option and sells a European put option. The options have the same underlying asset, strike price, and maturity. Describe the trader's position. Under what circumstances does the price of the call equal the price of th..

Reviews

Write a Review

 

Electrical Engineering Questions & Answers

  Define the winding resistance and leakage reactance

A 415V to 11 kV transformer has a rating of 200 kVA. The winding resistance and leakage reactance when referred to the primary are 0.014 and 0.057 ohms respectively.

  Determine the value at which the zeros are located

For a transfer function with a pair of complex zeros located on the j (omega)-axis, what happens to the frequency response as the frequency applied to the system approaches the value at which the zeros are located

  What is minimum bandwidth necessary to support the signals

If a 250 us period clock signal must be transmitted with a 10 kHz data signal on the same link, then what is the minimum bandwidth necessary to support both signals.

  What amount voltage is required to obtain the field

Electrons in silicon carbide have a mobility of 1000 cm^2/V-sec. At what value of the electric field do the electrons reach a velocity of 3 X 10^7 cm/s Assume that the movility is constant and independent of the elctric field.

  How many sio2 molecules are stacked on top of the gate oxide

If the thickness of gate oxide for a MOS transistor is about 100A, about how many SiO2 molecules, on average, are stacked on top of each other to form the gate oxide

  Give explanation to electric circuits

Explanation to "Electric circuits" question, The voltage across a load is v(t) = 260 sin (377t + 10 °) and the current through the load is i = 100 sin (377t + 10°). What is the RMS power?

  What is the average velocity in each section of pipe

Seawater with a specific weight of 64.0 lbs/ft^3 is at a level of 4 feet above the centerline of the exit pipe. The tank is closed at the top and there is a pressure of 1 psig above the seawater. What is the velocity at the end of the pipe

  Determine the step response of y of the system for all n

(a) Impulse Response of a DT LTI system is given by h[n]=(.2^n)u[n] Determine the step response of y[n] of the system for all n. (b) Given h[n]=(a^n)u[n] and x[n]=(.2^n-5)u[n-5] Evaluate y[n]=h[n]*x[n] for

  Calculate the percentage of electricity generation

Calculate the percentage of electricity generation by these fuel-cell systems compared to the annual electricity generation in the U.S. of 3.8x109 MW-hrs

  What is the maximum value of n0 for an fm cell phone

What is the maximum value of N0 for an FM cell phone whereby ST=

  Use laplace transform techniques

Use Laplace transform techniques to find the solution to the following differential equation given that x = 1/3 at t = 0.

  Draw graph of rms value of total current as function of f

Parallel plate capacitor. Plates have area of 2x2cm2 and interplate seperation is 1mm. Insulator inside capacitor has dielectric constant εr=4. Voltage across capactior has 10V amplitude.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd