What point along the pipe will the steam begin condensing

Assignment Help Mechanical Engineering
Reference no: EM131337477

A 50-mm-diameter, thin-walled metal pipe covered with a 25-mm-thick layer of insulation (0.085 W/m·K) and carrying superheated steam at atmospheric pressure is suspended from the ceiling of a large room. The steam temperature entering the pipe is 120°C, and the air temperature is 20°C. The convection heat transfer coefficient on the outer surface of the covered pipe is 10 W/m2 ·K. If the velocity of the steam is 10 m/s, at what point along the pipe will the steam begin condensing?

Reference no: EM131337477

Questions Cloud

Promoting the health and socialization benefits : Write a one-page letter to parents of 10-14 year old boys and girls, promoting the health and socialization benefits of water polo and encouraging them to introduce their children the sport through a local club. Tell them they can learn more about..
Do you agree with critique of the market in ewert article : Do you agree with the Critique of the market in Ewert's article? Why or why not? Read carefully and offer cogent reasons. Your answers must be at least 250 words
What are the needs for a successful management team : What are the needs for a successful management team? What are the tax implications for the legal form of business that you choose?
Calculate the net present value of the proposed expansion : International Foods Corporation, a U.S.-based food company, is considering expanding its soup-processing operations in Switzerland.- Calculate the net present value of the proposed expansion project.
What point along the pipe will the steam begin condensing : The convection heat transfer coefficient on the outer surface of the covered pipe is 10 W/m2 ·K. If the velocity of the steam is 10 m/s, at what point along the pipe will the steam begin condensing?
Purpose of the business research for study : Locate at least two peer-reviewed, business-research studies based on the industry in which you work or would like to work. Develop a 1,050-word evaluation of the critical first stage of the research studies:
Create adjusting journal entries at the end of the year : Create adjusting journal entries at the end of the year, December 31 based on the adjustment data. Prepare an adjusted trial balance. Prepare an income statement, statement of stockholders' equity, and classified balance sheet.
A large metal fabricator located in chama : The CEO has asked you to prepare a report on the situation. What factors (both within and outside of the firm) might account for this apparent discrepancy in performance?
What are some of the special communication issues : What are some of the special communication issues facing single parents? How can these issues be handled most constructively? Use the text plus 2 other sources to support your response. Please create this assignment in a word document.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the tension in cable ac

The boom OA carries a load P and is supported by two cables as shown. Knowing that the tension in cable AB is 183 lb and that the resultant of the load P and of the forces exerted at A by the two cables must be directed along OA, determine the tensio..

  Van der waals equation

Owing to safety requirements, the pressure within a 19.3 ft3 cylinder should not exceed 52 atm. Check the pressure within the cylinder if filled with 100 lb of CO2 maintained at 2128F using the

  A cylinder fitted with a piston contains 5 lbm of saturated

a cylinder fitted with a piston contains 5 lbm of saturated liquid water at 300 lbfin2. heat is slowly transferred to

  The system contains a sharp-edged entrace 6 threaded 90

a liquid at 10 c kinematic viscosity of 1.30710-6 m2s is to flow from a roof-top reservoir to a tanker truck through a

  Estimate by what percent the average air-water density is

the presence of raindrops in the air during a heavy rainstorm increases the average density of the air-water mixture.

  Compute the required pressure in the oil

a hydraulic cylinder must be able to exert a force of 45.5 kn. The piston diameter is 65 mm. Compute the required pressure in the oil

  Write down the truth table and draw a logic diagram

Prepare a 3-input, 5 bit multiplexer that fits in a 24-pin IC package. Write the truth table and draw a logic diagram and logic symbol for the multiplexer.

  A tank has two rooms separated by a membrane room a has 1

a tank has two rooms separated by a membrane. room a has 1 kg air and volume 0.5 m3 room b has 0.75 m3 air with density

  Find the magnitude and location of the maximum moment

How do the magnitudes of the biceps force B and joint reaction J change if the total weight w of the forearm and hand are included in the analysis and are assumed to act at the midpoint of the forearm?

  Determine the frequency response

A causal discrete-time LTI system is described by y [ n ) - h [ n - 1) + !Y [ n - 2) = x [ n ) where  x[ n ] and  y[ n ] are the  input  and  output  of  the  system,  respectively.

  Why is it often difficult to evaluate the elastic limit

Why is it often difficult to evaluate the elastic limit. What is the effect of poor alignment of the specimen. Why does a specimen that is properly aligned provide a more accurate estimate of the tensile strength compared to the estimate provided f..

  It is then heated to 450degc in the regenerator and then

in an ideal brayton cycle with regeneration air is compressed from 80 kpa and 10degc to 400 kpa and 180degc. it is then

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd