What is the volume of the solids in it

Assignment Help Civil Engineering
Reference no: EM13560256

1.A frictionless piston-cylinder contains 2kg of nitrogen at 100 kPa absolute and 300 deg K. The system is compressed polyprotically at a 1.4 exponent (n) until the nitrogen reaches a final temperature of 360 deg K.

Plot this process on a P-V diagram and a P-T diagram.

2.The solids in a specimen have a specific gravity of 2.65. If the oven-dry mass of the specimen is 25kg, what is the volume of the solids in it?

Reference no: EM13560256

Questions Cloud

Explain why this strategy should be adopted : A new strategy and explain why this strategy shouldbe adopted.
How can you prove that your answer is correct : Would it be possible to compact the above soil at a water content of 13.5% to a dry density of 2.00 Mg/m3? How can you prove that your answer is correct?
What is the magnitude of the corresponding force : A laser emits light at power 8.50mW and wavelength 633 nm. What is the magnitude of the corresponding force
How much will it cost for one 15 minute episode of heating : A room 4x5x6 meter is heated by a baseboard resistance heater. We want the heater to raise the room temperature from 7 to 23 deg C in 15 minutes. There are no heat losses from the room, and specific heat may be assumed constant. Power costs 15 cents ..
What is the volume of the solids in it : A frictionless piston-cylinder contains 2kg of nitrogen at 100 kPa absolute and 300 deg K. The system is compressed polyprotically at a 1.4 exponent (n) until the nitrogen reaches a final temperature of 360 deg K.
Discuss specific strategies blake : Discuss specific strategies Blake uses in critique of society in "London" and two of his other poems.
Apply the three internal analysis frameworks-swot analysis : Apply the three internal analysis frameworks-SWOT analysis
What is the undrained shear strength of the clat in kpa : A saturated clay deposit is vane-tested in-situ. A torque of 30Nm is required to shear the clat. The vane is 40mm wide by 100mm long.What is the undrained shear strength of the clat in kPa?
A rope-jumping rhyme : Who is "The Chorus Line: A Rope-Jumping Rhyme" addressed to? How is this chorus connected to Atwood's theme?

Reviews

Write a Review

 

Civil Engineering Questions & Answers

  Show how the gibbs energies of each of the phases vary

On a single graph, show how the Gibbs energies of each of these phases vary with temperature between - 20 C and 150 C for a constant pressure of 80 kPa. You can start your computations at the triple point

  Find the work done in pumping the water

a horizontal cylindrical tank 4 ft in diameter and 10 ft long is full of water. find the work done in pumping the water to a point 4 above the top of the tank.

  At what temperature will the rails touch end to end

The steel rails of a continuous, straight railroad track are each 60 ft long and are laid with spaces between their ends of 0.25 inches at 70 degrees F. At what temperature will the rails touch end to end

  Compute the energy loss in a 90 degree bend in a steel tube

Compute the energy loss in a 90 degree bend in a steel tube used for a fluid power system. The tube has a 0.5 inch outside diameter and a wall thickness of 0.065 inches. The mean bend radius is 2.00 in. The flow rate of hydraulic oil is 3.5 gal/mi..

  Calculate the total head loss for water flowing at 10

Calculate the total head loss for water (25°C) flowing at 100 m3/hr as shown in the following figure. The total flow length is 250 meters and the pipe is 15-cm diameter cast iron pipe

  Determine solids retention time and cell wastage flow rate

Using the following assumptions, determine the solids retention time, the cell wastage flow rate, and the return sludge flow ratefor the Jambalaya shrimp processing plant WWTP

  What is the minimum amount of carbon needed for absorber

You are assined the task of process design for a fixed-bed carbon adsorber system. You are given the following data: the inlet airstream flows at 5000 acfm (at 95 degrees F and 1 atm) and contains .2% n-pentane by volume

  Convert all quantities to si units then convert it to mph

Assume the plane is flying at an altitude of 32,810 ft (10 km), where the temperature is -8 C and the pressure is 250 mb. The Pitot-static tube measures a piezometric pressure difference corresponding to 1.206 psi. What is the airspeed in both m/s..

  Will promptly rate any acceptable response as a life saver

Write a brief description (1-3 paragraphs) of the Saint Venant equations (words only, no equations) comparing them to the Navier-Stokes equations, emphasizing the ASSUMPTIONS on which they are based.

  Determine the manning coefficient of channel roughness

A discharge of 2,200 ft^3/sec flows in a trapezoidal channel at a normal depth of 8.0 ft. The channel has a slope of 0.01, a 12-ft bottom width, and side slopes of 1:1 (H:V). Determine the manning coefficient of channel roughness

  Determine the minimum length of a crest vertical curve if

Determine the minimum length of a crest vertical curve if the grades are +4% and -2%, Design speed is 70 mi/h. State assumptions used in solving this problem.

  Determine the thermal efficiency of the cycle and net power

Steam at 550 degree Celsius, 17.5 MPa enters the high-pressure turbine of an ideal reheat Rankine cycle. The steam exits the high-pressure turbine at 2 MPa, is reheated to 550 degree Celsius, and then expanded through a low-pressure turbine

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd