What is the secondary side voltage and current

Assignment Help Mechanical Engineering
Reference no: EM13713129

A single phase step up transformer is used to transform 240VRMS to 2400VRMS. The transformer is operating at its rated power of 1kW (with purely resistive load), with transformer Reqp = 5, and a Xeqp = 4j, ignore the magnetising branch.

a. What is the primary side current in the transformer (Angle and magnitude)?

b. What is the secondary side voltage (Angle and magnitude)?

c. What is the secondary side current (Angle and magnitude)?

d. What is the real power output?

e. What is the efficiency of the transformer?

Reference no: EM13713129

Questions Cloud

Calculate the blackbody hemispherical spectral intensity : Calculate the wavelength (?) in ?m for maximum blackbody hemispherical spectral emissive power (E,b) at T = 750, 1500, 3000, and 5777 K. Calculate the temperature of a blackbody if its maximum hemispherical spectral emissive power (E,b) corresponds t..
Change in magnetic properties when steel is heated : Describe the theory used for the IZOD test and what units are used to report toughness? Explain the change in magnetic properties when steel is heated. Is this due to allotropic properties?
Conducted on a cylindrical specimen of a ceramic material : A three-point transverse bending test is conducted on a cylindrical specimen of a ceramic material that has a reported flexural strength of 533 MPa. If the specimen diameter is 4.4 mm and the support point separation distance is 50 mm, what is the ma..
Type of non-destructive testing method : Present an overview of (i) impact testing methods, and (ii) non-destructive testing (NDT) methods presented in your textbook. Elaborate on one type of impact testing as well as one type of non-destructive testing method. What are the advantages of us..
What is the secondary side voltage and current : A single phase step up transformer is used to transform 240VRMS to 2400VRMS. The transformer is operating at its rated power of 1kW (with purely resistive load), with transformer Reqp = 5, and a Xeqp = 4j, ignore the magnetising branch.
Three cables are used to tether a balloon as shown : Three cables are used to tether a balloon as shown. Determine the vertical force P exerted by the balloon at A knowing that the tension in cable AD is 481 N. Use a matrix linear equation solution method.
Saturated liquid water is kept in a piston-cylinder-weight : Saturated liquid water is kept in a piston-cylinder-weight assembly at 100 kPa. Heat is added from a reservoir at 120 C so that saturated vapor is formed. Estimate the absolute availabilities in kJ/kg of saturated liquid and vapor.
Supported by bronze rod and aluminum rod : Rigid bar ABC is supported by bronze rod (1) and aluminum rod (2), as shown. A concentrated load P is applied to the free end of aluminum rod (3). Bronze rod (1) has an elastic modulus of E1 = 15,000 ksi and a diameter of d1 = 0.45 in. Aluminum rod (..
Determoine the impulse that acted on the soccer ball : A soccer ball has a mass of 0.40kg. Initially it is moving to the left at 20 m/s, but then it is kicked and given a velocity at 45o upward and to the right, with magnitude 30 m/s.

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  A heat loss of 20 kjkg occurs during the process neglecting

a wind turbine with a 90m-diameter rotor is rotating at 30 rpm under steady winds at an average velocity of 25 kmh.

  What is the gage pressure of the air inside the piston what

consider the arrangement described in problem 1. a cable attached to the 100 lbm piston exerts a 200 lb force upward on

  Determine the total heat transfer and the total work

Determine the total heat transfer and the total work(kj). and show the T-V diagram.

  Methane ch4 at 25 c 1 bar enters a furnace operating at

methane ch4 at 25 c 1 bar enters a furnace operating at steady state and burns completely with 140 of theoretical air

  Determine 1 the energy flow rate of the oil at the inlet 2

for the following calculations take g 9.8ms2 and pwater1000kgm31. assuming there are both a pressure gage and a

  Assume the specific gravity of solids as 267 also determine

earth is required to be excavated from borrow pits for building an embankment. the wet unit weight of undisturbed soil

  How many square feet of collector would be required for a

the collecting panels of a solar boiler receive energy as heat at the rate of approximately 300 btuhr-ft2 of collecting

  Water at a flow of m 215 kgs is cooled from 82 degrees c

water at a flow of m .215 kgs is cooled from 82 degrees c to 42 degrees c by passing it though a thin-walled tube of

  The piston is now moved by changing the weights until the

argon in the amount of 0.6 kg fills a 0.05-m3 piston-cylinder device at 550 kpa. the piston is now moved by changing

  Define aeroplane dynamics

Aeroplane Dynamics, Determine the steady thrust that would enable a 200-tonne airliner to reach its take-off speed (75 m sâ?'1), from rest, in 30 s

  Calculate the overall aerosol mass removal efficiency for

an effluent stream consists of poly-dispersed aerosol of uniform density 1.8 gcm3. the particle size distribution is

  Consider condenser in a vapor power plant in which steam

consider condenser in a vapor power plant in which steam from the turbine is condensed to saturated liquid by rejecting

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd