Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
A factory has an electrical load of 1600 kW at a lagging power factor of 0.8. An additional variable power factor load is to be added to the factory. The new load will add 320 kW to the factory. The power factor of the variable power factor load is to be adjusted so that the overall power factor of the factory is 0.96 lagging.a) What is the reactive power associated with the added load?b) Does that load absorb or deliver magnetising vars (reactive power is also sometime referred to as magnetising vars. Inductors absorb magnetising vars and capacitors deliver magnetising vars)c) What is the power factor of the adjustable power factor load?d) If the voltage at the input is 2400 V(rms), what is the magnitude of the current into the factory before the adjustable load?e) What is the magnitude of the current with the adjustable load?
The following equation represents the complete combustion of ethane: 2C2H6(g) + 7O2(g) 4CO2(g) + 6H2O(g)At the same temperature and pressure what is the maximum volume in liters of carbon dioxide
Analysis of link budget DTH QPSK Satellite link, A direct-to-home satellite television system uses a geostationary satellite in orbit above the equator at a longitude of 109 degrees west.
The average voltage across the load when the triggering angle is 140 degrees. Keep in mind that the conduction is incomplete when the triggering angle is greater than 140 degrees.
(a) If the excitation volatge Eo is equal to the terminal voltage ( 4kv ), what is the maximum real power which the motor can deliver without losing synchronism (b) What is the rotor pole shift in electrical degrees
Design the combinational logic circuit for an elevator controller such that the option to go up or down by only one floor is disabled. Assume that the building the elevator is in has 4 floors. Your inputs are the current floor and the next request..
In a certain communications system a resonant-tuned circuit (tuned at 1200 kHz with Bandwidth = 15 kHz) is connected to the output of a non-linear amplifier (mixer). Find the frequency components at the output of the resonant-tuned circuit
A NEMA design B, 3-phase, 60 Hz, Induction motor is rated: 60 HP, 460V, 71A, 93.0% efficiency, NEMA code G, 1180 RPM: A. What is the power factor of the motor B. What is power factor of the motor when operating at 1/2 load
the -3 dB frequency for low pass Butterworth filter is 2.5 kHz. The stop band begins at 3.8 kHz, with an attention of 35 dB. Determine the minimum order of the filter if the sampling rate is 8 kHz
Consider a p-type semiconductor substrate with Na =10^15 cm^-3. A region of heavily p+ doped material is formed by ion implantation as shown in the sketch below.Derive an expression for the built-in voltage under equilibrium conditions.
Calculate the PMOS device with to acheive symmetric propagation delays in an inverter (tPLH = tPHL). Use Wn=450nm Ln =300nm and Lp=300nm and solve for Wp. So I think by some ratio I can find what Wp should be, maybe something like Wn/Ln=Wn/Lp
"Divide by 3 clock with 50% duty cycle" is the most commonly asked ASIC design question. This solution gives a simple design in which only 1 counter is required which works only on positive edge of the clock.
What fixed point unsigned representation, with how many bits and how many bits to the left of the binary point, should we use if we need to represent numbers in the range 0 - 100 with a resolution of .001 or better
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd