What is the rated wind speed for the wind turbines

Assignment Help Mechanical Engineering
Reference no: EM13717310

The Adair wind farm was commissioned in 2008 by MidAmerican Energy. The wind farm, located in Iowa on the border of Adair County and Cass County, is composed of 76 Siemens wind turbines each with a rated capacity of 2.3 MW. Each wind turbine has a rotor diameter of 93 meters, a power coefficient (coefficient of performance) equal to 75% of Betz’ law, and a combined gearbox and generator efficiency of 96%. It is estimated that the wind farm generates 437 GWh of electricity each year. Each wind turbines requires 400 hours of maintenance each year. The density of air is 1.225 kg/m3.

a. What is the overall efficiency of the wind turbines (%)?

b. What is the capacity factor of the wind farm (%)?

c. What is the rated wind speed for the wind turbines (m/s)?

d. What is the availability of the wind turbines (%)?

Reference no: EM13717310

Questions Cloud

Determine the heat transfer and work for this process : Ammonia as a saturated vapor at 130 psi expands is thermally in an internally reversible process to a pressure of 18 psi. Determine the heat transfer and work for this process.
Compute the weight percent sulphur : Compute the weight percent sulphur that must be added to completely crosslink an alternating chloroprene-acrylonitrile copolymer, assuming that 6 sulphur atoms participate in each crosslink.
The flow rate of liquid is large compared to the air : Consider an air cooler where the flow rate of liquid is large compared to the air, and the effectiveness, e, of the cooler is known to depend on the flow rate of air according to the relation, e ~ mair^-0.3 . The air inlet temperature is 25oC and the..
Consider the unsteady flow of a fluid : Consider the unsteady flow of a fluid in the x direction through a control volume. The linear momentum of the fluid within the control volume is a function of time given by 180tî slug·ft/s, where t is in seconds and is a unit vector in the x directio..
What is the rated wind speed for the wind turbines : The Adair wind farm was commissioned in 2008 by MidAmerican Energy. The wind farm, located in Iowa on the border of Adair County and Cass County, is composed of 76 Siemens wind turbines each with a rated capacity of 2.3 MW. Each wind turbine has a ro..
Determine the mass flow rate through the inlet pipe : Water flows out through a set of thin, closely spaced blades as shown in Fig. P5.4 with a speed of V = 10 ft/s around the entire circumference of the outlet. Determine the mass flow rate through the inlet pipe.
What is free-stream dynamic pressure for this test condition : You are working as a flight-test engineer at the Dryden Flight Research Center. During the low-speed phase of the test program for the X-37, you know that the plane is flying at an altitude of 8 km. The pressure at gage 1 is 1550 N/m2, gage; the pres..
Plane strain condition incorporating thermal strains : Determine the stress matrix components and epsilon_zz for known epsilon_xx, epsilon_xy, epsilon_yy for a) plane stress and b) plane strain condition incorporating thermal strains
Deliver one thousand summer suits to taylor place : ABC Clothiers Inc., has a contract with Taylor and Sons, a retailer, to deliver one thousand summer suits to Taylor's place of business on or before May 1.  On April 1, Taylor senior receives a letter from ABC informing him that ABC will not ..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A convenient and secure attachment point for fall

a convenient and secure attachment point for fall protection lines is located 35 feet above ground level on the

  Find the rate of heat removed from the condenser

2 kg/s of steam enters a SSSF condenser at 10 kPa and 90% quality; and exits as saturated liquid at 10 kPa. Find the rate of heat removed from the condenser. Evaluate the entropy change in the boiler, and determine whether it is irreversible, reversi..

  Determine the final pressure and temperature

A piston/cylinder assembly in a car contains 12 in3 of air at 13 lbf/in2 and 68 F. The air is compressed in a polytropic process with exponent n = 1.25 to a final volume six times smaller. Determine the final pressure and temperature, and the heat tr..

  An oven 1300 f at a rate of 300 per min if the plates

at a production facility 1.2 in thick 2 ft x 2 ft square brass plates denisty532.5 lbmft3 and cp 0.091 btulbmf that are

  Determine the isentropic efficiency of the turbine

Steam enters an adiabatic turbine at 6 MPa, 600°C, and 80 m/s, and leaves at 50 kPa, 100°C, and 140 m/s (T0 = 25°C, P0 = 100 kPa). If the power output of the turbine is 5 MW,

  Calculate the highest velocityacceleration and jerk that

a cam is to be desinged for an automated part loader.using the motion equationsconstruct a chart that tabulates

  A piston-cylinder device contains steam initially

A piston-cylinder device contains steam initially at 1 Mpa, 450 degrees celcius and 2.5 m^3. Steam is allowed to cool at constant pressure until it first starts condensing. Show the process on T-v diagram with respect to saturation lines and determin..

  A helical compression spring is wound

A helical compression spring is wound using QQ&T A229 wire. The spring is needed to support a 25-lbf load after being compressed 1.5 in. Because of assembly considerations, the solid height cannot exceed 1.5 in and the free length cannot be more than..

  An automobile traveling at 90 kmhr rounds a long sweeping

an automobile traveling at 90 kmhr rounds a long sweeping curve of radius 250m. the air conditioner is on and the

  Diateletect mount using finite-difference method

You are a thermal design engineer and plan to design cooling solution for a computer chip. As a basic design, a chip (K_c=50W/m-K) is mounted in a dielectric substrate (K_s=5.0 W/m-k) and one surgace of the system is convectively cooled, while the re..

  Determine the exit mach number me exit velocity magnitude

air flows through a turbine airfoil passage in the shape of a converging-only nozzle with an exit cross-sectional area

  Saturated water vapor in a closed sysytem is condensed by

saturated water vapor in a closed sysytem is condensed by cooling it at constant pressure to a saturated liquid at

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd