What is the rate of energy change of the cylinder

Assignment Help Mechanical Engineering
Reference no: EM13710450

A 1m-long metal cylinder of 25cm radius is heated such that the axial temperature distribution at a certain instant of time is T(z)=a+bz+cz2 where a=900K, b=-500K/m and c=150K/m2 . What is the rate of energy change of the cylinder at this instant if the side surface is well insulated and the cylinder's thermal conductivity is 40W/mK?

Reference no: EM13710450

Questions Cloud

Estimate at what angle will the pendulum swing out : A small wheeled vehicle will be sent to the planet mars to explore its surface. The vehicle contains an accelerometer that consists of a small pendulum. at what angle will the pendulum swing out
The final temperature of the water vapor : Water in a vertical piston cylinder is heated at constant pressure of 10 bar. It is initially at 179.9 0C and has a specific volume of 0.1 m3/kg and is heated to a final specific volume of 0.248 m3/kg. Changes in kinetic and potential energies are ze..
What is their equivalent capacitance : Three capacitors of 2.0, 9.0, and 17.0 µF are joined together in parallel.  What is their equivalent capacitance
Find the allowed wave functions and corresponding energies : A particle is moving in a simple harmonic oscillator potential V(x) = (1/2)kx2, Calculate the allowed wave functions and corresponding energies
What is the rate of energy change of the cylinder : A 1m-long metal cylinder of 25cm radius is heated such that the axial temperature distribution at a certain instant of time is T(z)=a+bz+cz2 where a=900K, b=-500K/m and c=150K/m2 . What is the rate of energy change of the cylinder at this instant if ..
What is the acceleration of the frisbee : The horizontal coordinates of a Frisbee in a strong wind are given by x = -12 t +4t2 and y = 10 t -3t2 where x and y are in meters, and t is in seconds.  What is the acceleration of the Frisbee
Estimate the heat loss per unit length of the pipe : Saturated steam at 120oC is transported through a steel pipe of diameter 250 mm. The temperature of the outer surface of the pipe can also be assumed 120oC. The pipe is centeredin concrete of square cross section (400x400 mm). The outer surfaces of t..
What horizontal pushing force is required to slide : A 53.0-kg crate rests on a level floor at a shipping dock. What horizontal pushing force is required to slide the crate across the dock at a constant speed
How long will it take for the current in the circuit : An unchanged 8.80- µF capacitor is in series, through a switch, with a 4.90-Mohm resistor and a 16.0- V battery (with negligible internal resistance.) How long will it take for the current in the circuit to drop to 0.37Ii

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  The temperature of the parallel surfaces at the both ends

consider a 1-cm-diameter and 0.3-m-long copper rod kcopper 400 wm-k with its ends fixed to two parallel surfaces. the

  Now heat is transferred to the water until the volume

a piston cylinder device initially contains 1.4 kg saturated liquid water at 200 oc. now heat is transferred to the

  The outer surface of the heater is exposed to a fluid with

a very thin electric heater is wrapped around the outer surface of a long cylindrical tube whose inner surface is

  Air enters an evaporative cooler at 1 atmosphere 36degc and

air enters an evaporative cooler at 1 atmosphere 36degc and 20 percent relative humidity at a rate of 4 m3min and it

  If i mev of energy is deposited in an anthracene crystal

in anthracene scintillation photons have a wavelength of 447 nm. if i mev of energy is deposited in an anthracene

  Time grain diameter min mm 21 00592 97 00823 a what was the

the average grain diameter for some metal alloy was measured as function of time at 650degc which is tabulated below at

  The front of a jet engine acts as a diffuser receiving air

the front of a jet engine acts as a diffuser receiving air at 900 kmh -5degc 50 kpa bringing it to 80 ms relative to

  A race car starting from rest travels along a straight road

A race car starting from rest travels along a straight road and for 10 s has the acceleration shown. Construct the v - t graph that describes the motion and find the distance traveled in 10s.

  Determine the yield strength modulus of elasticity tensile

in a tensile test the starting gage length 100 mm and the cross-sectional area 150 mm2. during testing the following

  The coefficient of restitution is 09 between the two

the coefficient of restitution is 0.9 between the two 60-mm-diameter billiard balls a and b. ball a is moving in the

  A certain fluid at 10 bar is contained in a cylinder behind

a certain fluid at 10 bar is contained in a cylinder behind a piston the initial volume being 0.05m3. calculate the

  If the outer race rotates at 500 rpm what is the maximum

a 25-mm series 02 single-row deep-groove ball bearing carries a radial load of 500 lb and an axial thrust load of 350

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd