What is the minimum piv rating for the diode

Assignment Help Electrical Engineering
Reference no: EM131261789

Repeat Prob. 3.100 for a full-wave bridge rectifier circuit. Draw the circuit

Problem 3.100

A 2800-V, 2-A, dc power supply is to be designed with a ripple voltage ≤ 0.5 percent. Assume that a half-wave rectifier circuit (60 Hz) with a capacitor filter is used.

(a) What is the size of the filter capacitor C?

(b) What is the minimum PIV rating for the diode?

(c) What is the rms value of the transformer voltage needed for the rectifier?

(d) What is the peak value of the repetitive current in the diode? (e) What is the surge current at t = 0+?

 

Reference no: EM131261789

Questions Cloud

What is the surge current when power is first applied : Simulate the AM demodulator in the EIA on page 122. Compare the spectra of the voltages across the two capacitors. The full-wave rectifier in Fig. P3.104 is operating at a frequency of 60 Hz, and the rms value of the transformer output voltage is ..
What is the size of the filter capacitor c : A 3.3-V, 30-A dc power supply is to be designed with a ripple of less than 2.5 percent. Assume that a half-wave rectifier circuit (60 Hz) with a capacitor filter is used.
Explain elements that make up methods competitive advantage : Based on what you heard in the video, does method have a marketing plan? -  Explain the elements that make up method's competitive advantage. Is it sustainable?
Why is a free and uncontrolled media important in a country : Explain how each of the six factors contributes to a civil society. - Why is a free and uncontrolled media important in a country?
What is the minimum piv rating for the diode : A 2800-V, 2-A, dc power supply is to be designed with a ripple voltage ≤ 0.5 percent. Assume that a half-wave rectifier circuit (60 Hz) with a capacitor filter is used.
Explain the concept of ethical behavior : Explain the concept of ethical behavior. - It is sometimes said that ethics hold a person to higher standards than laws. Explain.
Explain the difference between ethics and morals : Explain the difference between ethics and morals and describe the relationship between the two. - What are the differences between pre-conventional morality, conventional morality, and post-conventional morality?
Is sustainability a viable concept for americas businesses : Describe at least three situations in which you would not purchase the products of a firm even though it is very socially responsible.
Identify aspects of database design that can be denormalized : Identify the key determinants that could affect the degree of normalization of a database. Justify your response. Next, identify the aspects of the database design that can be denormalized. Explain the key ways in which the business rules support ..

Reviews

Write a Review

Electrical Engineering Questions & Answers

  How many delay bins do the multipath components fall

In a CDMA system the chip duration is 0.26us and maximum excessdelay 1.3us, into how many delay bins do the multipath components fall if the maximum excess delay is 100ns is the CDMA system narrowband or wideband

  What is the major difference between the lm324 and the lf347

From a high-level perspective, what is the major difference between the LM324 and the LF347. Which of the performance characteristics are significantly different because of this.

  What is the max voltage that can be measured by voltmeter

A galvanometer has 25 divisions in full scale. Its sensitivity (k) is .2mA/div and resistance (Rg) is 50 ohms. Construct voltmeter using the galvanometer and a 2950 ohms resistor, how will you use the resistor (series or parallel to galvanometer)

  Why are preemphasis and deemphasis used in the case of fm

Develop the circuit corresponding to Illustration 182 and carry out the comparison of PM and FM yourself.

  Design a state sequencer using d flip-flops and nand gates

The unused states have to be taken care of in such a way that Even numbered unused states will go to state 7 and Odd numbered states will go to state 3. The combinational logic portion of the circuit should use NAND and NOT gates only.

  Consider a 4-bit counter made with jk flip-flops

Consider a 4-bit counter made with JK flip-flops with preset and clear inputs. Describe the changes/additions that need to make the counter reset after counting to 1001. Be sure to state any assumptions that are made.

  Explain the difference between the input and output times

Show and explain how you could make a 2-bit counter that will count up or down on an external control signal. Explain the difference between the input and output times.

  Find condition on r so that the circuit is bibo unstable

Suppose L=25mH, but the resistance value,R, is not specified. Find a condition on R so that the circuit is strictly BIBO unstable (i.e., not even marginally stable). Hint: you might not be able to purchase such a resistor at Radio Shack

  What maximum current will be drawn from the output

What maximum current will be drawn from the 5V output of a peripheral device connected to an HCS12 input port. What input resistance does this represent.

  Determine the output resistance of the circuit

Determine the output resistance of the circuit in Fig. 7.19(a) and compare the result with that in the above example. Assume M1 and M2 are in saturation.

  Is the energy of the signal finite and why

f(t) = A[u(t) + u(-t/2-5)-1], where u(t) is the unit step function. Is the energy of this signal finite? Why or why not. If it exists, find the energy of this si

  What is the peak magnitude of b of the incident wave

A circular loop TV antenna with 0.02 m2 area is in the presence of a uniform amplitude 550 MHz sinosoidal signal. When oriented for maximum response, the loop develops an emf with a peak value of 30 mV.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd