What is the maximum column load in kips that could be placed

Assignment Help Civil Engineering
Reference no: EM13564985

1.The stream from a gas well is a mixture containing 50 mol % methane, 10 mol % ethane, 20 mol % propane, and 20 mol % n-butane. This stream is fed into a partial conderser maintained at a pressure of 250 psia, where its temperature is brought to 80 degrees F. Determine the molar fraction of the gas that condenses and the compositions of the liquid and vapor phases leaving the condenser.

2.What is the maximum column load in kips that could be placed on a 4-ft square temporary footing on a sand for which the standard resistance is about N=15 and the water table is at the surface? A factor of safety of 2 is to be maintained against bearing failure.

Reference no: EM13564985

Questions Cloud

What are the density volume-to-capacity ratio and level : A 5% upgrade on a six-lane freeway (three lanes in each direction) is 1.25 mi long. On this segment of freeway, the directional peak-hour volume is 3800 vehicles with 2% large trucks and 4% buses (no recreational vehicles), the peak-hour factor is 0...
How much heat had to be transferred to the vessel : Alkaloids are chemical compounds containing nitrogen that can be produced by plant cells. In an experiment, an insulated closed vessel 1.673 m3 in volume was injected with a dilute water solution containing two alkaloids: ajmalicine and serpentine.
Calculate the axial strain and the transverse strain in the : A rigid rectangular shelf is suspended from a rigid ceiling by mean of four rods of diameter .505 inches. The two rods to the left L1 and L2, are made of steel
What is the stress along the top edge and the bottom edge : A horizontal pre-stressing force of 500kN is applied to rectangler beam. the beam has a depth of 500mm and a width of 250mm. the force is applied at a distance of 80mm below the x-x axis. what is the stress along the top edge and the bottom edge caus..
What is the maximum column load in kips that could be placed : What is the maximum column load in kips that could be placed on a 4-ft square temporary footing on a sand for which the standard resistance is about N=15 and the water table is at the surface? A factor of safety of 2 is to be maintained against beari..
Determine the percent error n in replacing the sine and the : Determine the percent error n in replacing the sine and the tangent of an angle by the value of the angle in radians for angle values 5 degrees, 10 degrees, and 20 degrees. Explain the qualitative difference between the sine and tangent results
Determine the design esal if the design life is 20 year : A six-lane divided highway is to be designed to replace an existing highway. The present AADT (both directions) of 6000 vehicles is expected to grow at 5% per year. Assume SN = 4 and pt = 2.5
Calculate the extreme-fibre stresses at mid-span : Calculate the extreme-fibre stresses at mid-span for a simply supported prestressed concrete beam with a depth of 750mm, width 370mm and span of 7m under working live load of 65 kN/m and self-weight. The prestressing force.
Calculate the maximum pressure developed when a 10 in. thick : Calculate the maximum pressure developed when a 10 in. thick wall 10 ft high is to be poured at the rate of 3ft/hr at a temperature of 70 degrees F.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Specify the method that is used to determine the moments

For load combination 1.2D + 1.6L, determine the maximum negative moment in each span and maximum negative moment at each support. remember that live loads shall be placed so as to cause the greatest effect.

  What is the change in the strips width and thickness

Thin rubber strips are used to provide increasing resistance to orthopedic patients during large motion exercises. The sheets shown are 0.03125 in thick and 3 in. wide. Say the rubber properties are 120 psi and v= 0.47.

  Write brief description of 3-dimensional unsteady equation

Write a brief (No more than a few paragraphs plus the equations themselves on a) description of the three-dimensional unsteady Navier-Stokes equations as applied to water.

  Determine whether the crystal structure for the alloy

If the densities of metals A and B are 4.27 and 6.35 g/cm3, respectively, whereas their respective atomic weights are 61.4 and 125.7 g/mol, determine whether the crystal structure for this alloy is simple cubic

  Determine the corresponding value of the normal stress

a 60 -m- long steel wire must not strech more than 48mm when the tension in the wire is 6 kn. determine the corresponding value of the normal stress.

  The pipe entrance is flush and square edged

Water flows through 800 feet of 12-inch diameter iron pipe (? = 0.0018 inches) between 2 open storage tanks, whose water surface elevation difference is 16 feet. The pipe entrance is flush and square edged

  Find the required diameter for a single barrel culvert

A concrete culvert is required to convey a design flow of 654 cfs over a length of 330 ft, and a slope of .015ft/ft. Because there is a large lake downstream, the tailwater elevation is constant at 536.3 ft MSL

  What must be the rated horsepower of the motor

An automobile has been designed to maintain a constant speed of 55 mph on a +5% grade. The weight of the vehicle when fully loaded is 6000 lbs. What is the total resistance in still air of this vehicle?

  Determine when the queue will dissipate

A toll booth on a turnpike is open from 8:00AM to 12 Midnight. Vehicles start arriving at 7:45AM at a uniform deterministic rate of six per minute until 8:15AM and from then on at two per minute

  What amount will accumulate at time of her retirement

She plans to deposite 5% of her yearly salery, into retirment fund that earns 7% intrest compounded daily. what amount will accumulate at time of her retirement?

  How long will it take for the pce to reach the well

The water is pumped out of the aquifer at a rate of 2000 gpd, treat it with activated carbon and then put it back into the aquifer. At the flow rate how long until al the PCE is removed, assume carbon removed 100% of the PCE (ans. 54 days)

  How much natural gas is needed to incinerate this gas

The preheaded waste gas stream of 4,000 ACFM is entering a thermal oxidizer. The waste gas stream temperature is 1000 F. How much natural gas is needed to incinerate this gas stream at a temperature of 1500F?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd