What is the lowest temperature resolution

Assignment Help Mechanical Engineering
Reference no: EM13703902

A thermocouple with a sensitivity of 0.0225 /o mV F is used to measure temperature with a 16-bit A/D converter. If the full scale voltage of the A/D converter is 100 mV,

a. What is the lowest temperature resolution?

b. What is the range of temperature can be measured from zero?

Reference no: EM13703902

Questions Cloud

What is the moment about the origin due to the applied force : As shown, a member is fixed at the origin, point O, and has an applied force F, the tension in the rope, applied at the free end, point B. The force has magnitude F = 150 N and is directed as shown. The dimensions are x1 = 0.450 m, x2 = 1.90 m, y1 = ..
Determine the largest axial load : The w 310 * 129 structural A -36 steel column has a length of 4 m. If it's bottom end is fixed supported while it's top is free determine the largest axial load it can support use a factor f safety with respect to buckling of 1.75. E = 210 GPa , QY =..
Calculate lattice parameter and atomic radius of niobium : Niobium has the BCC structure with a density of 8.57 g/cm^3 , an atomic weight of 92.91 g/mol. One atom is associated with each lattice point. Calculate the lattice parameter; and the atomic radius of Niobium.
Calculate the theoretical density : Calculate the theoretical density of FCC Copper, which has an atomic radius of 0.128 nm and the atomic weight of 63.55 g/mol.
What is the lowest temperature resolution : A thermocouple with a sensitivity of 0.0225 /o mV F is used to measure temperature with a 16-bit A/D converter. If the full scale voltage of the A/D converter is 100 mV, What is the lowest temperature resolution? What is the range of temperature can ..
Temperature-heat flux are plotted assuming radial symmetry : The temperature and heat flux are plotted assuming radial symmetry, that is, even though the sensors are on both sides of the center line, they are plotted from one side only. Discuss whether or not you feel this is a good assumption. If so, are ther..
Origin of the cartesian coordinate system : As shown, a 3.1-lb ball is suspended at point D inside a box with dimensions w=9.50 ft, d=6.50 ft, and h=4.50 ft. The ball is held in place by three cables anchored at points A,B, and C on the surface of the box.
Utility approach and indifference curve yield : Prove that utility approach and indifference curve yield the same consumer equilibrium
How much energy was transferred to the room : You arrive home from a winter trip and turn on your baseboard (resistance coil) heater to warm the room. It remains on for 52 minutes, during which time it steadily consumes 3 kW of electricity. How much energy was transferred to the room in kJ?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Obtain the continuity equation in cylindrical coordinates

obtain the continuity equation in cylindrical coordinates by expanding the vector form in cylindrical coordinates. to

  A natural gas-fired furnace in a textile plant is used to

a natural gas-fired furnace in a textile plant is used to provide steam at 130 c. at times of high demand the furnace

  Determine the power developed by the turbine

Water vapor enters a turbine operating at steady state at 1000°F, 140 lbf/in2, with a volumetric flow rate of 12.6 ft3 /s, and expands isentropic ally to 2 lbf/in2. Determine the power developed by the turbine, in hp. Ignore kinetic and potential ene..

  A steel insert of 60mm internal diameter and 70mm external

a steel insert of 60mm internal diameter and 70mm external diameter is shrunk with a diameteral interfernce of 0.1mm

  Find a the diameter of the ball b the ball temperature just

a 0.010 kg 10 gram round ball of solid lead at 280 k initially moves at 400 ms passing horizontally through atmospheric

  Determine the efficiency and the horsepower output if the

a four-stroke-cycle engine operates on the air-standard diesel cycle. the engine has six cylinders with a 0.105 m bore

  Determine the ratio db for which a the maximum stress will

a couple m will be applied to a beam of rectangular cross section that is to be sawed from a log of circular cross

  Determine the rate of heat loss from the molten salt

Determine the rate of heat loss from the molten salt per meter length of the pipe.

  Determine for this machine the slip factor isentropic

a centrifugal compressor delivers 20 kgs of air at 0.32 mnm2 when running at 17500 rpm and absorbing 2800 kw. the inlet

  Minimum wall thickness of pole after incorporating factor

Erected a new sign welcoming people to the campus. The sign is painted on a rectangle of graphite reinforced epoxy which will not bend and measures 3 ft high and 5 ft wide. This sign is fastened along its 3 ft side to a hollow 2014-T6 aluminium (allo..

  What would the person weigh on the moon

The acceleration due to gravity at sea level is g = 9.81 m/s2 . What is the person"s weight at sea level? The acceleration due to gravity on the moon is g = 1.62 m/s2 . What would the person weigh on the moon?

  Calculate the volume flow rate of water through the pipe if

a venturi meter has an inlet of 250 mm and a throat of 150 mm diameter. its coefficient of discharge is .985. calculate

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd