What is the local heat transfer coefficient

Assignment Help Mechanical Engineering
Reference no: EM13701077

Air at a pressure of 1 ATM, a temperature of 15° C, and a velocity of 10 m/s flows over a 3 m long flat plate that is heated to a uniform temperature of 140° C.

a. What is the local heat transfer coefficient 3m from the leading edge of the plate?

b. Sketch, qualitatively, the manner in which the heat transfer rate (q) varies along the length of the plate (x).

Reference no: EM13701077

Questions Cloud

A piston-cylinder setup filled with air : A piston-cylinder setup filled with air, initially at 27 °C, 1 bar, changes to 17 °C, and 0.9 bar. Determine, as a present, the change in volume of the air from its initial volume. (in %)
Calculate the energy transfer for each of the components : An air standard dual cycle operates with a compression ratio of 15. At the beginning of the compression the conditions are 17°C, 0.95 bar, and 3.8L. The amount of heat added is 6.3 kJ, of which one-third is added at constant volume and the remainder ..
What might account for differences between equilibrium : In the textbook Sodium and Chlorine are listed as having ionic radii of 0.98 and 1.81 Å respectively. NaCl can form a face-centered cubic unit cell. What is the lattice constant of such a unit cell? What might account for the differences between the ..
Assuming complete combustion and constant specific heats : Calculate adiabatic flame temperature butane (C4H10) burning in air at 298 k and 1 atm, assuming complete combustion and constant specific heats
What is the local heat transfer coefficient : Air at a pressure of 1 ATM, a temperature of 15° C, and a velocity of 10 m/s flows over a 3 m long flat plate that is heated to a uniform temperature of 140° C. What is the local heat transfer coefficient 3m from the leading edge of the plate?
Calculate the average temperature of the plate surface : Air at atmospheric pressure and a temperature of 25°C is in parallel flow at a velocity of 5 m/s over a 1m long flat plate that is heated with a uniform heat flux of 1250 W/m2. Assume the flow is fully turbulent over the length of the plate.
Fluid is ethylene glycol under the same flow conditions : For a laminar boundary layer flow over a flat plate with air at 20°C and 1atm, the thermal boundary layer thickness Dt is approximately 13% larger than the velocity boundary layer thickness D. Determine the ratio D/Dt if the fluid is ethylene glycol ..
Piston cylinder device contains : A piston cylinder device contains .733 kg of refrigerant-134a at -10 degrees C. The piston that is free to move has a mass of 8.63 kg and a diameter of 21.2 cm. The local atmospheric pessure is 88 kPa. Now, heat is transferred to the refridgerant-134..
How many times can he jump on his bed before beam breaks : After one particularly wild night at the bars, Jon decides to come home and jump on his bed .Assume that he's jumping directly in between one steel support beam that's 10 foot long, 2 inches wide and 1 inch thick. Further assume that Jon weighs aroun..

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  An especially violent lightning bolt has an average

an especially violent lightning bolt has an average current of 1.37 103 a lasting 0.125 s. how much charge is delivered

  Effect of material hardness

On a single graph, plot "Hardness" as the ordinate versus "Aging Time" as the abscissa for each aging temperature - Discuss the effect of aging time and temperature on the effect of material hardness.

  Determine the temperature of the air at the exit in ordmc

at steady state air at 200 kpa 52 ordmc and a mass flow rate of 0.5 kgs enters an insulated duct having differing inlet

  Determine the average punching shear stress the circular

determine the average punching shear stress the circular shaft creates in the metal plate through section ac and bd.

  Calculate the effectiveness of the heat exchanger if the

a double pipe heat exchanger has an effectiveness of 0.5 when the flow is counter current and the thermal capacity of

  How many unit cells are there in the foil what is the mass

gold foil is 0.08 mm thick and 670 mm2 in area. a it is cubic with a 0.4076 nm. how many unit cells are there in the

  Determine the maximum amount that this buyer can afford to

a home buyer can afford to spend no more than 1500month on mortgage payments. suppose that the interest rate is 6 that

  1 kg of steam occupies a volume of 02 m3 at 9 bar in a

1 kg of steam occupies a volume of 0.2 m3 at 9 bar in a closed system. the steam is then heated at constant pressure

  Some helium gas leaks out of the container until the final

helium gas which may be treated as an ideal gas with r 386 ft-lbflbm- degree r is contained in a rigid 8-ft3 internal

  Then calculate the annual cost to operate a 60-w 75-w and

light bulbs are rated by their power consumption in watts w. electricity is sold in units of energy which is power

  The coefficient of friction between the load and the

the coefficient of friction between the load and the flat-bed trailer shown is 0.4. knowing that the speed of the rig

  What pressure would the air on the left need to be pumped

a partitioned tank contains water and mercury. what is the gauge pressure in the air trapped in the left chamber? what

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd