What is the local acceleration midway along the nozzle

Assignment Help Civil Engineering
Reference no: EM13316598

the velocity varies linearly with time throughout the nozzle. the velocity at the base is 1t and at the tip is 4t. what is the local acceleration midway along the nozzle when t=2s? What is the convective and centripetal acceleration with L=1.5ft?

Reference no: EM13316598

Questions Cloud

Deductions taken from his gross pay : Each employee has the following deductions taken from his gross pay: Federal Income Tax: 15% State Tax: 3.5% Social Security + Medicare Tax: 8.5% Health Insurance $75
Compute the net charge : A metal sphere has a charge of +6.9uc. What is the net charge after 7.6x10^13 electrons have been placed on it
Define accounting profit and economic profit : Define accounting profit and economic profit. When total sales revenue is $120,000, total costs $63,000, and total implicit costs is $33,000. Please calculate accounting profit and economic profit.
Find is there any conversion factor : how to convert ac current to dc current? is there any conversion factor? how to select an autotransformer for dc motors
What is the local acceleration midway along the nozzle : the velocity varies linearly with time throughout the nozzle. the velocity at the base is 1t and at the tip is 4t. what is the local acceleration midway along the nozzle when t=2s
Adopt islam in the postclassical period : Why did southeast Asian elites begin to adopt Islam in the postclassical period?
When the airplane is pointing vertically upward : Hello Since a prop-airplane can remain in horizontal flight indefinitely, why then, in the air shows, when the airplane is pointing vertically upward
Choose a pipe to be used as a tension member to resist : Choose a pipe to be used as a tension member to resist a service dead load of 10 kips and a service live load of 25 kips. The ends will be connected by welding completely around the circumference of the pipe.
Calculate the density of the cylinder of wood : We're doing a buoyancy lab and this equation is derived using the apparent mass of a sinker, calculate the density of the cylinder of wood

Reviews

Write a Review

 

Civil Engineering Questions & Answers

  Explain how to estimate the los at the corridor

An airport corridor is 30 ft wide. given a peak demand of 300 pedestrians per minute and an average walk speed of 3 ft/s, estimate the LOS at the corridor

  Design cyclone collection system which might meet the limits

Prepare a preliminary design of a system to collect dust from a plant under the following conditions: Sample of Dust: 50% by wt. below 30 micrometers; 80% by wt. below 70 micrometers Density= 2.5 g/cubic cmGas Flow Rate: 30,000 acfm (actual cubic fee..

  Calculate softening chemicals required in pound per milllion

given data of water softened by excess lime treatment, sketch a meq/l, calculate the softening chemicals required in pounds per million gallons, and draw a bar graph for the softened water after re-carbonation and filtration

  Discuss the dangers of optimization in terms of min section

Discuss the dangers of optimization in terms of minimum section to support loads. In other words, how would optimizing for bending stresses affect the shear capacity of a section

  Calculate the speed at impact on a large rock

A large rock became visible to a driver at a distance of 175 ft. Assuming a perception-reaction time of 0.8s, an initial speed of 42 mph, a coefficient of friction equal to 0.5, and a level roadway, calculate the speed at impact.

  Where the maximum ground level concentration would occur

a power plant burns 150,000 tonnes (1 tonne = 1,000 kg) of coal each year. The coal has 2.5% sulfur content, and the air pollution control equipment removals approximately 94% of sulfur. Assume 10% of the sulfur content ends up in the ash.

  What is p-value and find critical value of test statistic

The specification for a particular application calls for the blocks to have a mean compressive strength greater than 1350 kPa. A sample of 100 blocks is produced and tested.

  Determine the maximum internal pressure in mpa

The rivets are 10 mm in diameter, spaced a distance s = 24.4 mm apart, and have an average shear strength of 35 MPa. Determine the maximum internal pressure in MPa if the rivets are not to shear.

  Determine the overturning moment of silt and water

Assuming that silt is equivalent to a liquid having a density of 1760 kg/m3, determine the overturning moment of silt and water about point A.

  Determine what is the expected cycle service level

Demand for a particular product is normally distributed with a mean of 100 units and a standard deviation of 20 per period. if there are 120 units in inventory at the beginning of this period

  Force on block problem

The block is acted by its weight W=200 lb, a horizontal force Q=600 lb, and the pressure P exerted by the inclined plane. The resultant R of these forces is up and parallel to the inclined thereby sliding the block up it. Determine P and R.

  Find summer values for oxygen tranfer-hp and airflow rate

A fine-bubble aeration basin has a flow of 21.5 mgd, an influent BOD of 180 mg/l, 31 mg/l of mmonia, and effluent of 10 mg/l. During the winter, the wastewater temperature of 14.8 degrees C does not nitrify.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd