What is the level of service of this compound-grade freeway

Assignment Help Civil Engineering
Reference no: EM13549295

A segment of a four-lane freeway (two lanes in each direction) has a 3% upgrade that is 1500 ft. long followed by a 1000 ft 4% upgrade. It has 12 ft lanes and 3 ft shoulders. The directional hourly traffic flow is 2000 vehicles with 5% large trucks and buses (no recreational vehicles). The total ramp density for this freeway segment is 2.33 ramps per mile. If peak hour factor is .90 and all of the drivers are regular users, what is the level of service of this compound-grade freeway segment?

Reference no: EM13549295

Questions Cloud

What is the minimum detention time in hours to settle : A rectangular sedimentation basin will have a flow of 1.0 mgd using a 2:1 legth/width ratio, and overflow rate of 0.00077 fps, and a detention time of 3.0 hr. What will the dimensions of the basin be?
What is the value of the magnetic field at a distance : A solid cylindrical conductor is supported by insulating disks on the axis of a conducting tube with outer radius R_a = 5.75cm and inner radius R_b = 5.05cm . The central conductor and the conducting tube carry equal currents of
Determine the shear and moment diagram : A glass window contains a water body as shown below. Assuming the glass cross section is simply supported on the horizontal direction, and that the hydrostatic pressure varies with respect to depth as rho
Determine the minimum elevation difference across : The pressurized tank shown was fabricated by welding strips of plate along a helix forming an angle ? (beta) with a transverse plane as indicated below. Determine the largest value of
What is the level of service of this compound-grade freeway : A segment of a four-lane freeway (two lanes in each direction) has a 3% upgrade that is 1500 ft. long followed by a 1000 ft 4% upgrade. It has 12 ft lanes and 3 ft shoulders. The directional hourly traffic flow is 2000 vehicles with 5% large trucks a..
How do you calculate the critical depth of a circular : How do you calculate the critical depth of a circular concrete pipe with a diameter of 42 inches, a Manning's Number of .014, a slope of .025% and a flow rate of 10 CFS (cubic feet per second). The radius is 3.55 and normal depth is 25 inches
The mechanism that your firm should put in place : Hardly Able Contracting Co., Inc., Contractors and Engineers, has been in business for twenty five years and has been progressively expanding since the firm's inception
At what load would you expect this specimen to fracture if : Three-point bending test was performed on an aluminum oxide specimen having a circular cross section of radius 5.5 mm; the specimen fractured at a load of 850 N when the distance between the support points was 50 mm. Another test is to be performed o..
Explain what processes are required to be put into place to : In this assignment you are a recent graduate and have been hired as an industrial engineer and your job is to set up the plant to produce a new product.

Reviews

Write a Review

 

Civil Engineering Questions & Answers

  A cantilever beam is additionally supported using

A cantilever beam is additionally supported using two tierods. Both rods attach to the end of the beam. One rod comes off at 45 degrees and attaches

  Commercial management in civil engineering 1-critically

commercial management in civil engineering 1-critically analyse the use of project related commercial risk registers

  Determine the maximum height the projectile will reach

A projectile is fired up into the air at a speed of 161 m/s at an angle of 64° relative to the horizontal. Determine the maximum height the projectile will reach.

  Calculate required area of air to air heat exchange to cool

Calculate the required area of an air to air heat exchange to cool 20,000 cfm from 1200 F to 400 F. Assume ambient air at 80 F will be heated to 800 F by the exchange.

  Determine the location of the center of gravity of the cast

determine the location of the center of gravity of the cast aluminum block

  Determine magnitude of the horizontal and vertical component

A 3 m long curved gate is located in the side of a reservoir containing water. Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

  Calculate compressive capacity using australian standard

A client has engaged your consultancy company to undertake a conversion of a warehouse to a residential dwelling in the northern city of Darwin. You are required to check the capacity of a proposed column to ensure it can support a mezzanine floor..

  Determine what is the four lane freeways aadt

A four lane freeway (two lanes in each direction) operates at capacity during the peak hour. It has 11-ft lanes, 4-ft shoulders, and there are three ramps within three miles upstream of the segment midpoint and four ramps within three miles downst..

  Time inventory system for a product

How appropriate might a just in time inventory system be for a product such as roller skates?

  Compute the percent voids in total mix and percent voids

An aggregate blend is composed of 59% coarse aggregate by weight (sp. Gr. 2.635), 35% fine aggregate (Sp. Gr. 2.710), and 5% filler (Sp. Gr. 2.748). The compacted specimen contains 6% asphalt binder

  Find the steady state concentration if the air in the box

Consider the air over a city to be a box 100km on a side that reaches up to an altitude of 1.0 km. The air is blowing into the box along one of its sides with a speed of 4 m/s

  How long after the rope becomes taut until car b collides

The cars have equal mass. Car A is suddenly given velocity 4 m/s and the rope becomes taut. We know that 40 percent of the system's kinetic energy is lost during the rope tensioning.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd