User Account

All Pages

What is the k.e. of the satellite

Assignment Help Mechanical Engineering
Reference no: EM13212783

A satellite has been placed in a circular, sun-synchronous orbit at an altitude of 1300.0 km. The satellite has a mass of 5,000.0 kg. What is the K.E. of the satellite?

Reference no: EM13212783

Questions Cloud

Determine isentropic efficiency of the compressor : Carbon dioxide enters an adiabatic compressor at 100kPa and 300K at a rate of 0.5kg/s and exits at 600kPa and 450K. Considering constant specific heat, determine (a) isentropic efficiency of the compressor (b) the rate of entropy change in (kW/K) ..
What is the long run price per unit in the market : The MSU firm has the production function: q = f(L,K) = 4 L^(1/2) K^(1/2) The market has many firms identical to the MSU firm. The price of capital is r = 4 and the price of labor is w = 1 A. On the graph below: Draw the isoquant for q = 24, and th..
Determine the maximum angular velocity : The uniform rectangular plate is released from rest in the position shown. Determine the maximum angular velocity during the ensuing motion. Friction at the pivot is negligible.
Asset management strategic planning : Write a submission to your chief executive officer of your organisation describing a strategy to review and improve your organisation's assets, their management, and the standard of service which they provide, to achieve the board's goals.
What is the k.e. of the satellite : A satellite has been placed in a circular, sun-synchronous orbit at an altitude of 1300.0 km. The satellite has a mass of 5,000.0 kg. What is the K.E. of the satellite?
Calculate jack''s total variable cost and marginal cost : jack owns an auto repair shop, specializing in European cars. With three full-time mechanics, Jack's shop repairs/services 15 cars per week. Each worker is paid $500 per week. By hiring another mechanic, at the same salary, he can increase his wee..
Design the pump power and the diameter of brunching pipes : Design the pump power and the diameter of brunching pipes D1, D2, D3, so that the flow rate coming into all buildings are Q1=Q2=Q3=4.5m^3/hr, when all four valves v, V1, V2, V3 are open.
What is the rods angular velocity : A rigid bar of mass m and length L is released from rest in the horizontal position. What is the rod's angular velocity when it has rotated through 90°?
Explain how many moles of photons with a frequency : How many moles of photons with a frequency of 1.22e14 hz are necessary to produce

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the deflection of the beam

What load P allow can be supported at the midpoint of the bar if the yield stress in the steel wires is 220 MPa and in the aluminium wire is 80 MPa? A saftey factor of n = 2 is needed.

  What is the expected annual cost savings in dollars

A 50 hp motor with an efficiency of 0.80 is to be replaced by a newer model motor with an efficiency of 0.90. The motor is expected to operate 3000 hours per year. The cost of electricity in our area is $0.06 per kWhr.

  Determine the dimensions of the rack structure

The rack structure will be built 2 ft above floor level, and the clearance between the rack structure and the ceiling of the building must be at least 18 in. Determine the dimensions (height, length, and width) of the rack structure.

  Explain mechnical vibration analysis

Mechnical Vibration Analysis, How do I deduce the value of the viscous damping factor? How do I deduce the value of the viscous damping coefficient c?

  Prepare the statement of financial position

Prepare the statement of financial position

  Evaluate the exit velocity

Evaluate the valve closure to achieve a water exit velocity

  Determine the heat transfer by radiation

An air heater may be fabricated by coiling Nichrome wire and passing air in cross flow over the wire. Consider a heater fabricated from wire of diameter D=1 mm, L= 2m, electrical resistivity rho=10^-6 ohms, thermal conductivity k=25W/mK, and emiss..

  Explain square steel bar subjected to transverse biaxial

Consider a 4-in square steel bar subjected to transverse biaxial tensile stresses of 20 ksi in the x direction and 10 ksi in the y direction.

  Calculate the transverse modulus of the peek

calculate the transverse modulus of the peek/carbon fiber composite with 30% volume fraction by tow method. the modulus of peek is 3.8 GPa and the modulus of the carbon fiber is 400GPa. assume the reinforcing factor.

  How to create a directory called class

make a text file that contains what is your absolute path, and call it paths.txt

  Explain what is the tangential force

A spur gear has 48 teeth with a diametral pitch of 8 and a pressure angle of 20 deg. The face width is 0.75 inches. If the gear is transmitting 25 HP at 250 rpm

  Define centrifugal clutch

Centrifugal Clutch Question, In a centrifugal clutch there are eight shoes, each of mass 0.3 kg and the centre of gravity of each shoe is at 50 mm radius when it is just touching the drum of diameter 200 mm.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd