What is the highest elevation that can be achieved

Assignment Help Electrical Engineering
Reference no: EM13281488

We are imaging a field for NASA from a satellite. The field has vertical (sinusoidal) stripes that repeat at a rate of 1 stripe per meter. Our satellite has a CCD sensor (camera) that is 1 cm x 1 cm. This sensor has 1000x1000 pixels. The image on the sensor is (14/ z) as wide and as tall as the actual image on the ground for a height of z meters. What is the highest elevation (z) that can be achieved by the satellite such that the image of the stripes is adequately sampled? Hint: the Nyquist rate applies.

Reference no: EM13281488

Previous Q& A

  Explain mole ratio of tin to oxygen be too high

Spattering does occur and some of the sample is lost onto the laboratory bench. Will the reported mole ratio of tin to oxygen be too high, too low, or unaffected. Explain.

  Determine the set is linearly dependent or not

Determine if the set is linearly dependent or linearly independent

  When i went through the checkout process

When I went through the checkout process, It said that I would have access to the "ebook" version and because I need the access right away I ordered it however, I don't see where or how I get the ebook version can you please direct me to it?

  Evaluate the kinetic energy of the ejected electron

The work function (i.e binding energy) W, of cesium of metal is 3.43 x 10^-19 J. Calculate the kinetic energy of the ejected electron if light of frequency 1.00 x 10^15 s-1 is used for irradiating the metal.

  What is the return investors in xzx co

Given that investors who might invest in your project have the opportunity to invest in XZX Co., what is the opportunity cost of capital for your project? That is, what is the return investors in XZX Co. must be demanding is they are willing to pa..

  Explain number of moles of oxygen be too high

In an oversight in the experiment Jamie did not add the 4-5 additional drops of 6M HNO3. As a result, will the reported number of moles of oxygen be too high or too low in the final product. Explain.

  Find the velocity of the plane with respect to the ground

A plane is pointed in the positive x direction and is flying with an speed of (200, 0, 0) m/s relative to the air. Find the velocity of the plane with respect to the ground

  Katherine brewer is the owner and operator of personality sh

Katherine Brewer is the owner and operator of Personality Shine LLC, a motivational consulting business. At the end of its accounting period, December 31, 2013, Personality Shine has assets of $756,000 and liabilities of $181,000. Using the acc..

  Recuperation test of an open well the specific yeild

In a recuperation test of an open well the specific yeild was found to be 0.5. the diameter of well is 1 m and it is under a constant depression head of 4m. Find the discharge of the well?

  Contrast positivism with classical criminology

Contrast positivism with classical criminology and give an example of a theory that exists in each category.

Reviews

Write a Review

 

Similar Q& A

  Design a counter with the sequence utilizing two flip flops

Design a counter with the sequence 0-3-2-1-0 utilizing two flip flops. Flip flop A (MSB) is to be a JK type and Flip Flop B (LSB) is to be a RS Flip Flop.

  Determine what is the mean of x-normal random variable

If X is a normal random variable with standard deviation 4.00, and if the probability that X is more than 5.52 is .1271 (as shown below), then what is the mean of X? (Note: the diagram is not necessarily to scale.)

  Determine space between plates of a parallel-plate capacitor

The space between the plates of a parallel-plate capacitor is filled with a dielectric whose permittivity varies linearly from f1 at one plate (located at y=0) to f2 at the other plate (located at y=d).

  Design low pass active filter with a cutoff frequency

Design low pass active filter with a cutoff frequency t at 10kHz or more by 30db and have the pass band gain positive that does not deviate from 20db by more than 3db. The pass band frequency needed is 800Hz and below Derive transfer function

  Determine the total complex power provideed by the generator

A three-phase, 60Hz, wye-connected synchronous generator has balanced line-to-line voltages of 480V at its terminals. The generator is supplying power to two balanced and delta connected, three-phase loads. the first load is made up of three.

  What is the input impedance of the line if it is l km long

What is the propagation constant at 500 MHz. Use the fact that the velocity of an EM wave in a lossless air-filled line is the same as that of free-space propagation in air. That is, the propagation constant is the same.

  Determine at what speed should the machine be operated

A 450 piece/hr 10 hr B 500 piece/hr 8 hr A set of unsharpen ed tools costs $1,500 and can be ground 15 times. The cost of each grinding is $20. The time required to change and reset the tools is 2 hours, and such changes are made by a tool-setter.

  Find the load impedance in per unit to be used in impedance

One side of the transformer bank is connected to a 120-kV transmission line, and the other side is connected to a three-phase load of 10 MVA at 13.2kV and 0.8 lagging power factor. Using the base in the tranmission line of 120-kV and 20 MVA.

  Calculate the value required for the resistor labeled r

On a breadboards, hook up an IR LED to provide an infrared light source for signaling the phototransistor as shown in Figure 2 below. Use a pushbutton switch to turn the IR LED on and off.

  What is the adt output for a temperature of 81 degrees

A HCS12 ATD is set to 10-bit unsigned mode. The voltage references are set to ground and 1.0V What is the ADT output for a temperature of 81 degrees The temperature sensor measures 0 to 100 degrees with an output of 10 mV/degree.

  Determine the phase relation between vo and ig

Determine the phase relation between V o and i g for the given network if V g = 45sin(317t) and determine v o for the given network

  What is the bit rate of the corresponding pcm signal

A message signal, x(t) has a bandwidth of 15 kHz and an average power of 0.5 W. This signal is to be uniformly quantized with an input range of range of +-5 V. What is the bit rate of the corresponding PCM signal if the SQNR is to be greater than ..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd