Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
A 3400-lb car is traveling in third gear (ratio 2.5 to 1) on a level road at its top speed of 130 mi/h. The air density is 0.00206 slugs/cuft. The car has frontal area of 19.8 sqft, a drag coefficient of 0.28, a wheel radius of 12.6 inches, a drive axle slippage of 3%, and a drivetrain efficiency of 88%. At this vehicle speed, what torque is the engine producing and what is the engine speed (in revolutions per minute)?
a brass wire of diameter d=1/6 in is stretched between rigid supports with an initial tension T of 37lb. assume the coefficient of thermal expansion is 10.6X10^-6 / F and the modulus of elasticity is 15X10^6 psi.
A small chunk of the original sample had a wet weight of 140.9 grams and weighed 85.2 grams after drying. Compute the water content, using the correct number of significant figures.
A fluid film 0.1 mm thick separates solid and surface. The fluid viscosity is 0.04 N*sec/m^2. Assuming the velocity distribution in the film is linear, find the terminal velocity of the block. The area of the cube in contact with the film is 0.25 ..
Metallurgical balance in mineral processing, Assume 2000 short tons of ore were mined, 200 tones were rejected as waste and the tonnage accepted for metallurgical treatment
the unit weight of normal weight reinforced concrete is commonly assumed to be 150 lb/ft cubed. find the weight per lineal foot (lb/ft) for a normal weight reinforced concrete beam that: a. has a rectangular cross section 16 in.
Calculate the pH of a buffer solution prepared by mixing 8.5g KH2PO4 with 43.5g K2HPO4 in 1 liter of water (this is actually the composition of the dilution water used in a BOD test. Follow the same procedures you have been using for previous acid/..
a layer of clay, 5m thick, overlies a deposite of sand, 5m thick, which is underlaid by rock. the water table in the sand is sub-artesian with a level at 2m below fround level. the saturated unit weights of the clay and sand are 21 and 16 KN/m^3 r..
Assume a cross-sectional medial length of 32 in. (no stretching of the sheet due to bending). If the maximum shear stress must be limited to 19 ksi, determine the maximum torque that can be carried by the hollow section
A jet aircraft flies at a speed of 600 mph at an altitude of 40,000 ft. The atmosphere is the standard atmosphere. (1) What is the air pressure outside the aircraft (2) What is the Mach number of the flow around the aircraft
The PI is at station 250+50, the design speed is 65mi/h, and a maximum superelevation of 0.07 ft/ft is to be used. If the central angle of the curve is 38 degrees, design a curve for the highway by computing the radius and stationing of PC and PT.
Develop a simple urban constructed wetland design.
You plan to use a tank of total volume V= 10 m3 to remove a contaminant at concentration Cin = 1 g/m3 from a waste stream with a flow rate of Q = 1 m3/h. The reaction is first order with a rate constant k1 = 0.5 h-1.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd