What is the diameter of the solid steel shaft

Assignment Help Mechanical Engineering
Reference no: EM13703866

A solid round steel shaft, having an outside dameter of 2.002 in., is press or force fitted into the 2.00 in. hole in a gear. The force required to press the two machine parts together is 18,000 lb. What is the diameter of the solid steel shaft during this assembly operation?

Reference no: EM13703866

Questions Cloud

A weather balloon carries a mercury barometer : A weather balloon carries a mercury barometer in order to determine altitude as a function of flight time. At a particular moment, the barometer gives a reading of 558 mm. How high (in meters) is the balloon above standard sea level? (Assume mercury ..
A manometer on the discharge pipe of a pump handling : A manometer on the discharge pipe of a pump handling 8.4m^3/min of water shows a pressure of 3.7*10^5 Pa. The vacuum gage on the suction pipe shows a vacuum of 21 cm Hg. The vertical distance between the places of connection of the manometer and the ..
Find the time of flight : A mortar fires a projectile across a level field so that the range (R) is maximum and equal to 915 m. Find the time of flight.
Calculate the developed pump head and the total power input : Benzene, p= 54 lb/ft^3 at 100 F is pumped at a rate of 40 gpm. The reservoir is open to atmosphere and below the pump centreline by 4 ft. The discharge line is 10 ft above the pump centreline. The gage at discharge reads 50 psig. The discharge line i..
What is the diameter of the solid steel shaft : A solid round steel shaft, having an outside dameter of 2.002 in., is press or force fitted into the 2.00 in. hole in a gear. The force required to press the two machine parts together is 18,000 lb. What is the diameter of the solid steel shaft durin..
An air bubble with a radius : An air bubble with a radius of 0.5 cm is released from the regulator of a scuba diver swimming 30 m below the sea surface. Estimate the radius of the bubble just before it reaches the water surface. Assume that the pressure inside the bubble is equal..
Quick return mechanism is to be designed with a time ratio : A quick return mechanism is to be designed with a time ratio=1.22 and a cycle time of 0.2sec. What is the required crank speed (rad/s)? What are theta 1 and theta 2?
Diameter of solid steel shaft during this assembly operation : A solid round steel shaft, having an outside dameter of 2.002 in., is press or force fitted into the 2.000 in, hole in a gear. The force required to press the two machine parts together is 18,000 lb. What is the diameter of the solid steel shaft duri..
Driven along a straight track with position : A car is driven along a straight track with position given by s(t) = 150t – 300 ft (t in seconds). Find v(t) and a(t). Use calculus to find the displacement and total distance traveled over the interval [1, 4].

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  A shearing machine cuts flat sheet steel strips 100mm wide

a shearing machine cuts flat sheet steel strips 100mm wide by 25mm thick and 6j of work are required per square mm cut.

  Calculate 1 the material removal rate 2 the tangential

1. a lathe is set up to machine a taper of 1 mm per 10 mm on bar stock 120 mm in diameter. the chucked end is larger

  What is the percent change in viscosity per degree celsius

what is the percent change in viscosity per degree celsius for a vg-32 mineral turbine oil at 10c? at 120c? what are

  Finally it comes to a stop in one half a rotations what was

a 50 kg winding drum 75 cm in diameter is used to reel in cable. it is moving at the rate of 2 revolutions per second.

  If the barometric pressure was 100 kpa and the humidity was

temperature in state college pa on 31st december 2012 was 22 f. if the barometric pressure was 100 kpa and the humidity

  Two previously undeformed cylindrical specimens of an alloy

two previously undeformed cylindrical specimens of an alloy are to be strain hardened by reducing their cross-sectional

  Determine the temperature and pressure at the nozzle inlet

Helium gas enters a nozzle, whose isentropic efficiency is 95 percent with a low velocity, and it exits at 14.4 psia, 160 degrees F, and 940 ft/s. determine the temperature and pressure at the nozzle inlet.

  Determine the angle through which end d of shaft cd rotates

In the gear-and-shaft system shown, the shaft diameters are dab= 2 in. and dcd=1.5 in. Knowing that G = 11.2 x10^6 psi, determine the angle through which end d of shaft cd rotates.

  When the cylinder is filled to a depth of 70 inches with a

a cylindrical container has a 4.5 inch diameter and weighs 0.4 lbf when empty. when the cylinder is filled to a depth

  How much ideal effort force is required to travel up ramp

If a person and a wheelchair have a mombined weight of 185 lb how much ideal effort force is required to travel up the ramp? Can you just explain to me what equation I need for this?

  Determine the toal change in alength bcross-sectional

a quantum stabilizer made of cold-worked columbium is 15in long and has a rectangular crosssection 14in by 34in. for a

  Determine the rate of net energy loss

A house is maintained at 1 atm and 24 C and warm air inside a house is forced to leave the house at a rate of 150 m^3/h as a result of outdoor air at 5C infiltrating into the house through the cracks. Determine the rate of net energy loss of th..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd