What heat sink temp is necessary to ensure safe operation

Assignment Help Electrical Engineering
Reference no: EM13258880

A power transistor for which Tjmax=180degrees Celsius can dissipate 50Watts at a case temperature of 50degrees. If it is connected to a heat sink using an insulating washer for which the thermal resistance is .6degrees Celsius/Watt, what heat sink temperature is necessary to ensure safe operation at 30Watts? For an ambient temperature of 39degrees Celsius, what heat sink thermal resistance is required? If for a particular extruded aluminum finned heat sink, the thermal resistance in still are is 4.5degrees Celsius/Watt per centimeter of length, how long a heat sink is needed?

Reference no: EM13258880

Questions Cloud

What about the employees themselves : What about the employees themselves? Do they inflate their duties or act differently if they know they are being watched during a job analysis? How can we level for this if we suspect it is occurring?
Present value of the given annuities : What is the present value of the following annuities? a. $2,500 a year for 10 years discounted back to the presentat 7 percent b. $70 a year for 3 years discounted back to the present at3 percent
Design an active first-order rc low-pass filter : Design an active first-order RC low-pass filter (using a 741 op-amp) with a cut-off frequency of 10 kHz and a band-pass gain of 20 dB. Derive the step response and voltage transfer function.
What is the after-tax cost of preferred stock : A firm is paying an annual dividend of $2.65 for its preferred stock which is selling for $57.00. There is a selling cost of $3.30. What is the after-tax cost of preferred stock if the firm's tax rate is 33%?
What heat sink temp is necessary to ensure safe operation : A power transistor for which Tjmax=180degrees Celsius can dissipate 50Watts at a case temperature of 50degrees. If it is connected to a heat sink using an insulating washer for which the thermal resistance is .6degrees Celsius/Watt
Which method provides for more goal congruence : Compare the evaluation of the office managers that would be made under the original table and the table you have justcreated.
Discuss any implications the court : Refer back to the Appendix you studied in Unit I on pages 22-24 regarding reading and briefing cases. Taking this information, prepare a brief of the Smith v. Murrell case on pages 303-304.
Find the brewster angle : When red light in a vacuum is incident at the Brewster angle on a certain type of glass, the angle of refraction is 31.0°. What is the Brewster angle
Provide the journal entry for the periods payroll : The payroll register of Lowry Landscaping Co. indicates $1,260 of social security withheld and $315 of Medicare tax withheld on total salaries of $21,000 for the period. Federal withholding for theperiod totaled $3,822. Provide the journal entry f..

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Explain how the ideal op amp is a high-gain amplifier

The current through a branch in a linear network is 2 A when the input source is 10 V. If the voltage is reduced to 1 V and the polarity is reversed, the current through the branch is a. - 2 A b. - 0.2 A c. 0.2 A

  Describe what is the mass of licl in a unit cell

Lithium chloride crystallizes in a face-centered cubic structure. The unit cell length is 5.14 10-8 cm. The chloride ions are touching each other along the face diagonal of the unit cell. The lithium ions fit into the holes between the chloride io..

  Calculate the velocity of the holes and electrons

(a) Calculate the velocity of the holes and electrons in this material. (b) What doping level is necessary to provide a current density of 2 mA/micrometer^2 under these conditions? Assume the hole current is negligible.

  Calculate the intracellular concentration of sodium

Assume that life on Mars requires cell potential to be +100mV, and the extracellular concentrations of the three major species are following (mmol/L): Na+ : 145; K+ : 4; Cl- : 120. Choose one species and assume that other two permeabilities are ze..

  Estimate the propagation delays of implementations

Estimate the propagation delays of implementations (1), (2) and (3) using typical propagation delay data in the timing specifications of the logical gates of CD4000 family. Take the average propagation delay for 1-0 and 0-1 output transitions.

  Represent the timer as a box labeled 30 s timer

The system contains a door sensor, a window sensor, and a key activation switch. If the switch is on, opening the window will set off the alarm immediately. Opening the door will start a 30 second timer.

  Design combinational logic circuit that compare 2- bit num

Design a combinational logic circuit that compare two 2- bit number. The circuit must have three outputs indicationg if the two numbers are equal, first larger than the second, or the second is larger than the first.

  Determine the full load current of single phase motor

A 50HP single phase motor operates from a 480V, 60HZ supply. When delivering full rated power the motor efficiency is 89% and the power factor is 0.78 lagging. Determine the full load current.(Hint: 746W=1HP)

  Explain power factor

Power Factor, A single phase electric motor has an output power of 10 kW and an efficiency of 90% at full load. The motor is fed from a 240 V supply via a cable that has a resistance of 10 milli ohms per metre length.

  Find amount of work in foot-pounds required to empty trough

A trough is 8 feet long and 1 foot high. The vertical cross-section of the trough parallel to an end is shaped like the graph of y=x^{8} from x=-1 to x=1 . The trough is full of water. Find the amount of work in foot-pounds required to empty

  Methods used to eliminate noise from a spatio-temporal

Methods used to eliminate noise from a spatio-temporal signal, Name and describe, in detail, 2 methods used to eliminate noise from a (spatio-temporal) signal. This question requires a clear, detailed explanation of the methods. Mathematical equation..

  Give numerical values for the step heights at the interface

A window is etched through a 500 nm thick oxide on a [100] silicon wafer. The wafer is re-oxidized at 1100 °C using wet oxidation to grow a 750 nm thick film inside the window. Draw a cross-section of the wafer following the second oxidation.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd