What are the final pressure and temperature inside the tank

Assignment Help Mechanical Engineering
Reference no: EM13711608

An adiabatic vessel contains steam at 180 [C] and 116 [kPa]. The volume is 0.5 [m^3]. Steam at 150 [C] with a quality of 0.85 is fed into the vessel until the flow stops.

1) What are the final pressure and temperature inside the tank?

2) What is its quality, and is it greater than, equal to, or less than the initial quality? Why?

3) Find the minimum quality in the feed stream needed to ensure that no liquid water remains after filling the tank.

Reference no: EM13711608

Previous Q& A

  Erythroblastosis fetalis (ef) is a condition

Erythroblastosis fetalis (EF) is a condition that causes the mother's red blood cells to attack those of the baby as if they were any foreign invaders. It is referred to as hemolytic anemia of the newborn. It is caused by anti-Rh antibodies fr..

  Find the state of the escaping fluid

A pipe system carries a steam-water mixture at 250 psi, 95% quality. A leak develops in the pipe allowing the fluid to escape to the building which is at atmospheric pressure. Treating the leak as a throttling process, find the state of the escaping ..

  Calculate mass needed to achieve mechanical noise limit

For mass-spring-damper accelerometer, calculate the mass needed to achieve mechanical noise limit a_rms = 1 nG if the mechanical resonance frequency is to be f=100 Hz.

  Types of consequences of operant conditioning

Man's Best Friend: The Biology and Behavior of Dogs Describe a response that can be classified as classical conditioning (such as vet trips, grooming, thunder phobia, etc.) Describe four types of consequences of operant conditioning?

  In air-conditioning systems-streams of cold and warm air

In air-conditioning systems, streams of cold and warm air are mixed to get air with the right temperature. Consider a mixing chamber into which cold air enters at 8C and 100 kPa at a rate of 0.55 m^3 /s and warm air enters at 300C and 100 kPa. The ra..

  Range of projectile and velocity on impact given inputs

(MATLAB) given a cannon ball that is shot upwards at an angle, the time taken for the cannon ball to hit the ground is: Write a single function that outputs the total time of flight, range of projectile and velocity on impact given inputs. Use the fu..

  A woman is admitted to the emergency room

A woman is admitted to the emergency room because the tissues in her legs are retaining water. She is diagnosed with severe pitting edema-any pressure applied to the swollen tissue leaves a temporary indentation or "pit" in the tissue, even wh..

  What is coefficient of restitution needed for good ammo

A "pumpkin chucker" designed for the annual pumpkin competition held near Millsboro, delaware every fall (first week of November) uses a pneumatic launcher (air cannon) to throw its pumpkin. It is important to know if your "ammunition", the pumpkin, ..

  Difference between causes and effects in the swot analysis

Difference between causes and effects in the SWOT analysis.Causes are important, not effects. Once the SWOT Analysis is created, each group needs to construct the SWOT Bivariate Strategy Matrix.

  Shell-and-tube heat exchanger is used to cool flow of steam

A shell-and-tube heat exchanger is used to cool a flow of steam using a stream of cooling water. The steam enters the heat exchanger at 0.1 bar and a quality of 91% (state 1), and exits as a saturated liquid at the same pressure (state 2). The mass f..

Reviews

Write a Review

 

Similar Q& A

  A bicyclist starts from rest after traveling along a

a bicyclist starts from rest after traveling along a straight ath a distance of 20m reaches a speed of 30kmh. find his

  What equal amount can you withdraw from the account at the

today you have a savings account of 15 620. based on an annual interest rate of 4.2 what equal amount can you withdraw

  A rocket launched vertically upward is being monitored by a

a rocket launched vertically upward is being monitored by a radar located at a distance 1.2 km from the launch pad. the

  Determine the final temperature of the water use the

a closed well-insulated tank contains 0.15 kg of liquid water. the tank base is a copper plate of mass 0.25 kg that

  Compute and plot the chemical potential surface microtp for

compute and plot the chemical potential surface microtp for a monoatomic ideal gas in the range 5 klttlt1000 k and 10-5

  Determine the cop of the device when extracting thermal

a thermoelectric unit consists of n cells. when there is no temperature difference across the leads the resistance is 4

  What is the value of heat transfer coefficient at this

the temperature profile at a location in water flowing over a flat surface is experimentally measure to be tdegc

  Where a is a scaling constant and v is the relative speed

wind drag can be approximated as being quadratic in speedfd av2where a is a scaling constant and v is the relative

  Neglecting changes in kinetic and potential engery and

a heat exchanger at an industrial plant uses river water to condense 2x105 kgh of steam from saturated vapor to

  Steam in a piston-cylinder assembly undergoes a polytropic

steam in a piston-cylinder assembly undergoes a polytropic process with n2 from an initial state where p 500 psia and

  What is the mass moment of inertia about an axis parallel

an object has mass of 2 kg and radius of gyration of e 1.5m. what is the mass moment of inertia about an axis parallel

  Find the maximum permissible unbalance

A centrifugal pump, weighing 600N and operating at 1000 rpm, is mounted on six springs of stiffness 6000 N/m each. Find the maximum permissible unbalance in order to limit the steady-state deflection to 5mmm peak-to-peak.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd