Water flow in pipe can be represented by the reynolds number

Assignment Help Mechanical Engineering
Reference no: EM13705898

Water flow in a pipe can be represented by the Reynolds number Re which is dimensionless.

The Reynolds number is determined by the equation Re= (w Vw Dp ) / ?w where:

w = water density = 1.94 slug/ft3

Vw = water velocity = 156 km/s

Dp = pipe diameter = 8.5 in

?w = water viscosity = 4x10-4 kg/m-s

Part A: Do a dimension check to show that Re is dimensionless (i.e. use M, L, t, etc.)

Part B: Determine the value of Re using the values given above

Reference no: EM13705898

Questions Cloud

What will the tanks pressure be at that point : A 680 liter oxygen tank is filled to the pressure of 13.7 Mpa, and used to help a respiratory patient in a room with a temperature of 20 degrees C. During one treatment, 135 Liters of oxygen is supplied from the tank to the patient. The tank is then ..
What is the phase and the specific volume of water : What is the phase and the specific volume of water at 3000 Kpa and 455 degrees C? Show this state on a PV diagram
Number of electrons transferred during the corrosion process : Determine the number of electrons transferred during the corrosion process. (T = 25°C and symmetry factor = 0.5)
Calculate the gap developed between bone and cement : A bioengineer is trying to determine the amount of gap developed between bone and cement when a femoral hip is placed. The system is assumed to consist of concentric cylinders. Calculate the gap developed between bone and cement if the temperatures o..
Water flow in pipe can be represented by the reynolds number : Water flow in a pipe can be represented by the Reynolds number Re which is dimensionless. The Reynolds number is determined by the equation Re= (w Vw Dp ) / ?w where:
Resultant internal bending moment : The member has a square cross section and is subjected to a resultant internal bending moment of M = 850 Nm as shown. Determine the stress at each corner and sketch the stress distribution produced by M. Set theta = 30 (dimensions 250mm by 250 mm)
What wind velocity and barometric pressure : On a beautiful day your ship sights a water spout in the East Indian Ocean. You fix your position as 6000 ft from the spout and record a wind velocity of 10 ft/s. What wind velocity and barometric pressure does a fishing boat 600 ft from the spout ex..
Automobile is accelerated : 040 kg automobile is accelerated from 5 kmph to 70 kmph. What is the average power (in hp) required if this is done in 7 s?
Find the force and the velocity generated by the piston : A hydraulic cylinder has a piston diameter of 2.2 inches, a fluid pressure of 1100 psi, a flow rate of 132 cubic inches per minute, and a stroke of 10.5 inches. Find the force and the velocity generated by the piston.

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  The telescope mirror design was approved and a container

a team of astronomers have proposed to construct a large parabolic telescope mirror by spinning a cylindrical container

  The convective heat transfer coefficients at the inside and

the inside temperature of a furnace is 1300oc and outside wall temperature is 40oc. the furnace wall is made up of 23

  The mass of the piston is such that a cylinder pressure of

10 kg of water in a piston-cylinder arrangement exists as saturated liquidvapor at 100 kpa with a quality of 50. it is

  The acceleration of point a is defined by the relation a

the acceleration of point a is defined by the relation a -1.8 sin kt where a and t are expressed in ms2 and seconds

  The rigid bar is orginally horizonal and is supported by

the rigid bar is orginally horizonal and is supported by two cables each having a cross-sectional area of 0.05in2 and

  12 lbm of carbon c reacts with 24 lbm of oxygen o2 to form

12 lbm of carbon c reacts with 24 lbm of oxygen o2 to form 22 lbm of carbon dioxide co2 plus an unknown amount of

  Determine the diameter of the standard commercial steel

a pump is located 4.5 m to one side of and 3.5 m above a reservoir. the pump is designed for a flow rate of 6 ls. for

  Natural gas fired plants at these prices and express the

suppose that coal costs 45ton at the power plant fuel oil costs 60bbl 1 bbl has appoximately 6?106 btu 6 mmbtu and

  Saturated water at 10 bar will be supplied to the shell

the exhaust gas from a diesel-powered electric generation plant will be used to generate steam in a shell-and-tube heat

  How does this compare to the tabulated value of 5164 ft3lbm

assuming that steam can be treated as an ideal gas what would the specific volume of steam be at 600deg f and 120 psia

  Paint plant air house

Electricity might be used to run the fan to draw air through the system, and also to run a chiller - What is a typical COP for a commercial chiller?

  Te well stirred mixture leaves the tank at the same rate

a tank is filled with 8 gallon of brine in which 2 lb of salt is dissolved. brine having 3 lb of salt per gallon enters

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd