Use the approximation equation for contact stress

Assignment Help Mechanical Engineering
Reference no: EM13718973

A gear set has a module of 5mm, a 20° pressure angle, and a 24-tooth case-iron spur pinion driving a 48-tooth case-iron gear. The pinion is to rotate at 50 rev/min. What horsepower input can be used with this gear set if the contact stress is limited to 690 MPa and F=60mm? Use the first approximation equation for contact stress, not the AGMA equations.

Reference no: EM13718973

Questions Cloud

Suspended in a room filled with saturated steam : A 1.2-cm-diameter silver sphere initially at 25°C is suspended in a room filled with saturated steam at 100°C. Using the lumped system analysis, determine how long it will take for the temperature of the ball to rise to 50°C. Also, determine the amou..
How long will it take for the surface temperature : A long aluminium cylinder 50cm in diameter is initially at a uniform temperature of 200°C. It is suddenly subjected to a temperature of 70°C and h = 535W/m2K. How long will it take for the surface temperature to reach 100°C.?
Aerodynamics of a new prototype automobile a scale model : To test the aerodynamics of a new prototype automobile a scale model will be tested in a wind tunnel. For dynamic similarity, it will be required to match Reynolds number between model and prototype.
Determine the safety against the brittle fracture : An engineering member is to be made of 18-Ni maraging steel (vacuum melted). The member is a plate loaded in tension, and it may have a crack in one edge. The dimensions are width b=35 and t=5.0mm, and the crack may be as long as a=7.0 mm.
Use the approximation equation for contact stress : A gear set has a module of 5mm, a 20° pressure angle, and a 24-tooth case-iron spur pinion driving a 48-tooth case-iron gear. The pinion is to rotate at 50 rev/min. What horsepower input can be used with this gear set if the contact stress is limited..
Final equilibrium temperature and entropy generation : A container filled with 73 kg of liquid water at 99ºC is placed in a 60-m3 room that is initially at 12ºC and 1 atm. Thermal equilibrium is established after a while as a result of heat transfer between the water and the air in the room. Using consta..
Determine the final mass of the tank : An insulated rigid tank contains 5 kg of helium gas at 440 kPa and 31C. A valve is now opened, and helium is allowed to escape until the pressure inside drops to 200 kPa. Assuming the helium remaining inside the tank has undergone a reversible, adiab..
Pressure driven flow between stationary parallel plates : Consider the pressure driven flow between stationary parallel plates separated by distance b. Coordinate y is measured from the bottom plate. The velocity field is given by u=U(y/b)[1-(y/b)]. Obtain an expression for the circulation about a closed co..
Rigid tank is divided into two equal parts by a partition : An insulated, rigid tank is divided into two equal parts by a partition. Initially, one part contains 6.06 kmol of an ideal gas at 155 kPa and 30C, and the other side is evacuated. The partition is now removed, and the gas fills the entire tank. Dete..

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  Sketch the two processes in series on a t-v diagram

a sealed piston-cylinder assembly contains 3 lbm of water. the water is initially at p1 40 psia and t1 300degf. the

  There is a current of 360 a in the wire in the presence of

a wire has a length of 7.20 10-2 m and is used to make a circular coil of one turn. there is a current of 3.60 a in the

  A30 l sample of gas at 25 deg c 10 atm and is cooled to 0

a gas stream containing acetone vapor in air leaves a polymer drying process. a 3.0 l sample of gas at 25 deg. c 1.0

  The two tanks are allowed to reach equilibrium and the

a 5-ft3 tank contains 0.6-gravity natural gas at 700 psia and 60of. this tank is connected to anther tank containing

  Assuming that the force exerted by the pitcher on the ball

major league baseball training camps are now just beginning. given a baseball with a mass of 9 ounces estimate the work

  It is observed that the wire stretches 45 mm when a tensile

an 18-m-long steel wire of 5-mm diameter is to be used in the manufacture of a pre-stressed concrete beam. it is

  For one-dimensional steady state conduction in

for one-dimensional steady state conduction in cylindrical or spherical shell without heat generation is the radical

  A piston mp 5 kg is fitted in a cylinder a 15 cm2 that

a piston mp 5 kg is fitted in a cylinder a 15 cm2 that contains a gas. the setup is in a centrifuge that creates an

  Determine the smallest horizontal force required

Determine the smallest horizontal force required to lift the 260- crate. The coefficient of static friction at all contacting surfaces is = 0.7. Neglect the mass of the wedge.

  Determine the radius of curvature of the trajectory and the

a ball is released with the initial velocity of 80 ftsec at an angle of 35 degrees. determine the radius of curvature

  Water steam at 3mpa and 400oc is expanded to 100kpa in an

water steam at 3mpa and 400oc is expanded to 100kpa in an adiabatic turbine with an isentropic efficiency of 92.

  A shearing machine cuts flat sheet steel strips 100mm wide

a shearing machine cuts flat sheet steel strips 100mm wide by 25mm thick and 6j of work are required per square mm cut.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd