Use 3 terms of taylor series to estimate the velocity at

Assignment Help Mechanical Engineering
Reference no: EM13624085

The velocity of falling parachute is computed as:

v(t)=(gm)/c (1-e^-((c/m)t))

Where, g=9.8m/s2; m=

50kg; c=12.5.

Use 3 terms of Taylor series to estimate the velocity at t=6sec using v(t=0). What is the percentage relative error.

Reference no: EM13624085

Questions Cloud

The final specific volume and b plot the process pressure : 1 given three kilogram of gas in a piston-cylinder assembly undergo a process during which the relationship between
Current in a circuit falls from 50 a to 00 a in 01 s if an : current in a circuit falls from 5.0 a to 0.0 a in 0.1 s. if an average emf of 200 v induced give an estimate of the
Calculate the maximum value of current in the coil : a circular coil of radius 8.0 cm and 20 turns is rotated about its vertical diameter with an angular speed of 50 rad
A newspaper article reported that a poll based on a sample : a newspaper article reported that a poll based on a sample of 1150 residents of a state showed that the states
Use 3 terms of taylor series to estimate the velocity at : the velocity of falling parachute is computed asvtgmc 1-e-cmtwhere g9.8ms2 m50kg c12.5.use 3 terms of taylor series to
Calculate the maximum power kw that could be developed by : a site near an ocean is being evaluated for power generation using wind turbine. the site is observed to have steady
The other end of the rod is in contact with a circular : a 1.0 m long metallic rod is rotated with an angular frequency of 400 rad s-1 about an axis normal to the rod passing
Determine the average punching shear stress the circular : determine the average punching shear stress the circular shaft creates in the metal plate through section ac and bd.
Te velocity of point p relative to frame a is vpa -149 i : the velocity of point p relative to frame a is vpa -14.9 i 19.4 j fts and the acceleration of p relative to frame b

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  Determine the normal component of the particles

the motion of a particle is defined by the equations and x 2t t2m and yt2m where t is in seconds.a determine the

  Determine the air velocity

A Pitot-static probe connected to a water manometer is used to measure the velocity of air. If the deflection (the vertical distance between the fluid levels in the two arms) is 7.3 cm, determine the air velocity. Take the density of air to be 1.2..

  The sliding distance after the first 05 seconds g if the

it takes 0.5 seconds for one to lift the cart handle from 0 to 450 in a linear way around o. if the block has a mass of

  Determine the values of t

the motion of a particle is defined by the position vector r=a(cos t + t sin t)i + A(sin t-t cos t)j, where t is expressed in seconds. Determine the values of t for which the position vector and acceleration are.

  If the density of the aniline is 1002 kgm cube and the

a centrifuge bowl with 250mm internal diameter is turning at 4000 rmin. it contains a layer of aniline 50mm thick. if

  What is the largets size mm internal through crack that a

1 the critical crack length for a through crack in a thick plate of 7150-t651 aluminum alloy that is in uniaxial

  Determine a the boundary work needed for this process and

a piston cylinder device contains 2.5 kg of carbon dioxide co2 initially at 100 kpa and 300 degrees celsius.the co2 is

  Fr an output power of 316 hp we have nm 1483 rpm and ia

a shunt dc motor has ra 0.3 u03a9 and vt 999.9 v. for an output power of 31.6 hp we have nm 1483 rpm and ia 145.8 a.

  Thermal equilibrium between the lake water and the blocks

a 60-kg block of nickel at 5c and a 35-kg block of silver at 50c are placed in a very large lake where the water

  It supplies heat to a room at a rate of 46000 btuhr in

a heat pump has a second law efficiency of of 74. it supplies heat to a room at a rate of 46000 btuhr in order to

  Milk is pasteurized if it is heated to 63c for 30 min but

milk is pasteurized if it is heated to 63c for 30 min but if it is heated to 74c it only needs 15 seconds for the same

  Calculate real gas pseudopressure at a pressure

Calculate real gas pseudopressure at a pressure of 1902.7 psia using the following data and a base pressure of 102.7 psia. Was the calculation of real gas pseudopressure necessary for this gas? Explain your answer.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd