User Account

All Pages

Two tubes are available for a particular application 1 40

Assignment Help Mechanical Engineering
Reference no: EM13629050

Two tubes are available for a particular application: (1) 4.0 cm diameter circular tube and (2) 4.0 cm square tube. Air at 1 atm and 27 °C is blown across the tubes with a velocity of 20 m/s. The tube wall temperature is maintained at 50 °C in both cases.

a. Calculate the heat transfer for both geometries if the length of each tube is 1 meter.

b. Which tube should you recommend to your boss and why?

Reference no: EM13629050

Questions Cloud

The fibers have an outside diameter of 85 mum and an inside : a reverse osmosis unit for purifying dilute salt solution has 900000 hollow fibers that permit water and reject salt.
Find the area of the shaded region the graph depcits iq : find the area of the shaded region. the graph depcits iq scores of adults and those scores are normally distributed
Mary is in a train traveling at 30ms fred is standing next : mary is in a train traveling at 30ms. fred is standing next to the train tracks.the train passes fred at 30ms. 2m after
In a brinell hardness test a 1500-kg load is pressed into a : in a brinell hardness test a 1500-kg load is pressed into a specimen using a 10-mm diameter hardened steel ball. the
Two tubes are available for a particular application 1 40 : two tubes are available for a particular application 1 4.0 cm diameter circular tube and 2 4.0 cm square tube. air at 1
Find the indicated z score the graph depicts the standard : find the indicated z score. the graph depicts the standard normal distrubtion with mean 0 and standard deviation 1. the
The hot-air balloon shown below is tethered with three : the hot-air balloon shown below is tethered with three mooring cables. the force tb in cable db has a magnitude of 2230
In a tensile test on a metal specimen true strain 008 at : in a tensile test on a metal specimen true strain 0.08 at a stress 265 mpa . when true stress 325 mpa true strain
Assume the december low temperature distribution is normal : the average low temperature for marquette mi in december is 12f. the average low temperature for each of 8 randomly

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Air is expanded in a polytropic process with n 15 from 2

air is expanded in a polytropic process with n 1.5 from 2 mpa and 300 degrees celcius to 80 kpa in a piston-cylinder

  Find the speed of the bucket

(a) Find the speed of the bucket (b) How fast must the bucket move at the top of the circle so that the rope does not go slack?

  A standard steel specimen of 13 mm diameter elongated 22 mm

a standard steel specimen of 13 mm diameter elongated 22 mm when it was subjected to a tensile force of 29.5 kn if the

  After a load of 236 kn is applied the gage length increases

a carefully controlled tensile test is conducted on a metal alloy specimen. the original diameter is 10 mm and the gage

  Find the the acceleration of each mass

Two equal masses are connected on either side of a pulley. One of the masses rests on an inclined plane with angle of inclination of b. The other one hangs in mid air.

  The mechanical effficiency of the system is 80 what is the

it takes 15 seconds to raise a 1200 kg car and the supporting 300 kg hydraulic lift platform to a height of 2.8 m. the

  A mass of 10 kg is vertically accelerated from rest to 10

a mass of 10 kg is vertically accelerated from rest to 10 ms through a height of 100 m. the internal energy of the mass

  For a metal that has the simple cubic crystal structure

for a metal that has the simple cubic crystal structure calculate the atomic radius if the metal has a density of 8.38

  What magnitude f is required for the decelerating force

A luge and its rider, with a total mass of 98 kg, emerge from a downhill track onto a horizontal straight track with an initial speed of 39 m/s.

  A male reactor operator receives a whole body dose

a male reactor operator receives a whole body dose equivalent of 0.96 rem over a period of one week while working with

  Cutting conditions are v 25 ms f 03 mmrev and d 20 mm

a cylindrical workpart 125 mm in diameter and 900 mm long is to be turned in an engine lathe. cutting conditions are v

  A steady flow of 15 kgs of high-pressure liquid oil drives

a steady flow of 15 kgs of high-pressure liquid oil drives a hydraulic motor at the steady-state-steady-flow conditions

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd