The settling time does not change over range of gain values

Assignment Help Mechanical Engineering
Reference no: EM13717371

1. How can you tell from a root locus if the settling time does not change over a range of gain values?

2. What values of damping is associated when a pair of dominant poles Crosse the imaginary axis?

Reference no: EM13717371

Questions Cloud

Determine the rate of entropy change of the air : Air is compressed by 10.50-kW compressor form P1 to P2. The air temperature is maintained constant at 26ºC during this process as a result of heat transfer to the surrounding medium at 10ºC. Determine the rate of entropy change of the air.
What is the impulse delivered to the driver by the seat belt : hen it crashes into a bridge support that does not move, a car goes from 110km/h to 0 in 1.23 m. What is the impulse delivered to the 70-kg driver by the seat belt, assuming the belt makes the driver's motion identical to the car's motion
What is the quality of the steam at the inlet : In certain instances, there are problems when the state variables that is not temperature and pressure. Consider a throttling valve. In this case, a mixture of liquid and vapor enters a valve at 3MPa and leaves at 10KPa and 500C. Assume that the valv..
Find how long does the projectile remain in the air : You throw a snowball horizontally from the roof of a building that is 56.0 m above flat ground. The initial speed of the snowball is 11.0 m/s. How long does the projectile remain in the air
The settling time does not change over range of gain values : How can you tell from a root locus if the settling time does not change over a range of gain values? What values of damping is associated when a pair of dominant poles Crosse the imaginary axis?
Find the horizontal distance from the player to the basket : A basketball player shoots a ball at 14.4 m/s at an angle of 27.0° and a height of 6 feet 3 inches above the floor. Find the horizontal distance from the player to the basket
Find how far has the spring compressed by the time : A block of mass m = 1.00 kg slides along a horizontal table with speed v0 = 2.50 m/s. How far has the spring compressed by the time the block first momentarily comes to rest
An exothermic process occurs uniformly throughout : An exothermic process occurs uniformly throughout a 10-cm-diameter sphere (k = 300 W/m.K, cp = 400 J/kg.K, ? = 7500 kg/m3), and it generates heat at a constant rate of 1.2 MW/m3. The sphere initially is at a uniform temperature of 20oC, and the exoth..
Estimate how long does it take to hit the floor : You have two blocks with masses m1 and m2 suspended from a string looped over a pulley. how long does it take m2 to hit the floor

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  Show that the moment of inertia of n particles each of mass

use the principle of angular momentum to eventually derive the moment of inertia integral. for each case find the

  Advantage of using electric chiller and gas-fired chillers

What’s the C.O.P. for a 5-ton of gas fired (absorption) chiller uses 15 kw electric and 5 thermo gas? What would be the advantage of using electric chiller and gas-fired chillers in combination? How would you sequence their operations? How much chill..

  Consider a viscoelastic polymer rod that is stretched from

consider a viscoelastic polymer rod that is stretched from 100 mm to 165 mm by a stress of 3.35 mpa. while being held

  When the cylinder is filled to a depth of 70 inches with a

a cylindrical container has a 4.5 inch diameter and weighs 0.4 lbf when empty. when the cylinder is filled to a depth

  A piston-cylinder device contains helium gas

A piston-cylinder device contains helium gas initially at 145 kPa, 20 degrees C, and 0.5 m^3. The helium is now compressed in a polytropic process (PV^n = constant) to 400 kPa and 140 degrees C. Determine the heat loss or gain during this process.

  When designing a front end loader what considerations must

when designing a front end loader what considerations must you make in the machine how it might be used and the type of

  Calculate the actual a/f ratio and do a wet

Find the stoichiometric A/F ratio (by mass) for the combustion of benzene (C6H6). Compute the actual A/F ratio and do a wet and dry analysis of the products by volume at a mixture strength of 95%.

  Solve the velocity distributions in the two fluids

Solve the velocity distributions in the two fluids.

  Find the temperature of the combustion products of butane

find the temperature of the combustion products of butane when burned in an adiabatic steady flow combustor at 1atm

  Computing test mach number

Calculating Test Mach Number, The temperature in a reservoir of a supersonic tunnel is 519 deg.R. In the test section, the flow velocity is 1385 ft/s.

  The primary type of interior-automatic bonding between water

the primary type of interior-automatic bonding between water molecules in a solution in pure water is? deformation occurs when a material is subjected to enough tensile stress that it deforms in a shape but then returns to it is original diminuendos ..

  What is the concept they understood

To solve ax = b Find a number y such that ay is integer (and possibly a factor of b) Then if k Ay = b, the answer is ky What is the concept they understood?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd