The convective heat transfer coefficients at the inside and

Assignment Help Mechanical Engineering
Reference no: EM13645201

The inside temperature of a furnace is 1300oC and outside wall temperature is 40oC. The furnace wall is made up of 23 cm chrome brick, 11.5 cm fire brick and 11.5 cm of masonry brick. The convective heat transfer coefficients at the inside and outside furnace walls are 56.8 W/m2 K and 5.7 W/m2 K respectively.

Compute the following:

1. Overall heat transfer coefficient

2. Rate of heat transfer per unit wall area

3. The surface temperature at each layer of brick

4. Is the temperature of the fire brick within the allowable limit of 1090oC.

Reference no: EM13645201

Questions Cloud

Give a strategy that allows you to use the preceding : when light with a wavelength of 545 shines on a metal surface electrons are ejected with speeds of 3.1 x 105 ms or
Kuru is a prion disease of the fore people of highland new : kuru is a prion disease of the fore people of highland new guinea. kuru is similar to creutzfeldt-kakob disease. it was
How would you detect the presence of mercury in a sample : how would you detect the presence of mercury in a sample potentially containing other group 1 cations? detail the
This coil is placed inside a solenoid with coil and : a 3.5 cm diameter circular coil with 29 turns of wire has resistance 1.6 omega. this coil is placed inside a solenoid
The convective heat transfer coefficients at the inside and : the inside temperature of a furnace is 1300oc and outside wall temperature is 40oc. the furnace wall is made up of 23
To see why consider a 9 v battery supplying 30 a to an : opening switches in highly inductive circuits can be dangerous even with low-voltage power sources. to see why consider
Models of the pricing of stock options often make the : models of the pricing of stock options often make the assumption of a normal distribution. an analyst believes that the
A tablet of vitamin c was analyzed to determine whether it : a tablet of vitamin c was analyzed to determine whether it did in fact contain as the manufacturer claimed 1 g of the
If an alternator coil is 17 cm in diameter and is spinning : a car alternator produces about 14 v peak output to charge the cars 12- v battery.if an alternator coil is 17 cm in

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Design a v-beltchain drive which limits the top speed to

a mini motor bike for children is powered by 4 hp single cylinder gasoline engine governed to run at a maximum of 1850

  A container is supported by three cables that are attached

a container is supported by three cables that are attached to a ceiling as shown. determine the weight w of the

  Determine the net power output developed by the turbine in

steam at 160 bar 520 degrees celsius and with a mass flow rate of 250 kgs enters a turbine operating at steady state

  An air conditioner running with r-134a on a cycle executed

an air conditioner running with r-134a on a cycle executed under the saturation dome between the pressure limits of 0.8

  Determine the change in internal energy kj and enthalpy kj

two kg of saturated liquid water at 1 bar is compressed to 25 bar and 100degc in a water pump. determine the change in

  Determine the size of the equipment

Building HVAC Requirements - Indoor Air Quality and Mechanical Ventilation and how determine the size of the equipment if i need for 60cfm.?

  A manometer connected to the tap shows a head of 014 in of

a jet of air from a nozzle is blown at right angles against a wall in which a pressure tap is located. a manometer

  A closed system of mass 53 lb undergoes a process in which

a closed system of mass 5.3 lb. undergoes a process in which there is a heat transfer of 215 ft-lbf from the system to

  Water vapor h2o is heated during a steady-flow process at 1

water vapor h2o is heated during a steady-flow process at 1 atm from 298 to 2400 k at a rate of 0.6 kgmin. determine

  Compute next year sales and the sales for each quarter

Using the data in Problem , Meredith and Smunt Manufacturing expects sales of pumps to grow by 10% next year. Compute next year's sales and the sales for each quarter.

  Determine the normal force r between the wheel

Determine the normal force R between the wheel and the horizontal surface. Neglect the weight of the horizontal shaft.

  A 1050 hot-rolled steel of diameter 300mm has an ultimate

a 1050 hot-rolled steel of diameter 300mm has an ultimate tensile strength of sut724mpa that is hot-rolled is exposed

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd