Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
a component in a packaging machine is subjected to a tensile load of 36.6 KN which will be repeated several times over the life of the machine. The cross-section of the component is 12 mm thick and 20 mm wide. Specify a suitable material for the component assuming a safety factor of 1.5 and service factor of 2.
A tank is filled with oil (specific gravity 0.8) and water to a depth of 10 meter and 6 meter respectively. Find the resultant force from all fluids acting on the gate of 1.8 meter by 9 meter.
a spot speed study was conducted on a freeway on which the mean speed and the standard deviation were found to be 72 .4 mi/hr and 5.4 mi/hr, respectively. what is the range of the values that would be expected to contain the middle 95 percent of s..
Describe some of the benefits of physical models and mock-ups. What data are required to measure the following cost-effectiveness, system effectiveness, operational availability, and life-cycle cost?
Three prismatic bars, two of material A and one of material B, transmit a tensile load P. The two outer bars (material A) are identical. The cross-sectional area of the middle bar (material B) is 50% larger than the cross-sectional area of one of ..
The PI is at station 250+50, the design speed is 65mi/h, and a maximum superelevation of 0.07 ft/ft is to be used. If the central angle of the curve is 38 degrees, design a curve for the highway by computing the radius and stationing of PC and PT.
The ½ inch pipe was found to have an average friction factor of 0.0129 and the ¾ pipe had an average friction factor of 0.0209. The length of the pipes between the two manometer connections are 60 inches each.
A 0.25 in diameter copper rod BC is securely attached between two identical 1 in diameter steel rods (AB and CD). Find the load P if the total elongation of the system is measured to be 0.0312 in. Esteel= 29,000ksi, Ecopper=17,000ksi.
A 1.50 L buffer solution is 0.250 M in HF and 0.250 M in NaF. Calculate the pH of the solution after the addition of 0.0500 moles of solid NaOH. Assume no volume change upon the addition of base. The Ka for HF is 3.5 x 10 -4 .
Air pollution in a city is caused by the following four sources: vehicle exhaust (V), industrial exhaust (I), dust (D), and pollen from plants and trees (T). On a particular day, the likelihood of air pollution caused by these sources is 4:3:2:1, ..
A vehicle is traveling on a curved section of a road of radius 2500 feet at a speed of 60 mi/h. The motorist suddenly applies their brakes, causing the automobile to slow down at a constant rate. After 8 seconds the speed has been reduced to 45 mi..
Steam enters an adiabatic turbine steadily at 3 MPa and 300 *C and leaves at 70 Kpa and 100 *C. If the power output of the turbine is 2 MW, determine a) the isentropic efficiency of the turbine and b) the mass flow rate of the steam flowing throug..
Your neighbor has the Bonda generator in the next problem and they have graciously extended a 100 foot extension cord to your home, which has a resistance of 0.0075 ohms per foot of wire (per lead). By how much is the delivered power reduced
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd