Sketch hoop and radial stresses in the wall of cylinder

Assignment Help Mechanical Engineering
Reference no: EM13217019

a closed ended thick cylinder has the following dimensions which are internal radius is 0.1m and the external radius is 0.15m. the cylinder is subjected to an external pressure of Po=22MPa and an internal pressure of Pi. if the cylinder is designed according to the Tresca yield criterion, calculated the internal pressure Pi. the cylinder is made from steel where yield stress= 240 MPa and v=0.3. Subsequently sketch the hoop and radial stresses in the wall of the cylinder.

Reference no: EM13217019

Questions Cloud

The existence of a hazard-the hazard must be recognized : Describe and discuss how OSHA makes use of Section 5(a)(1) of the Act (commonly referred to as the general duty clause). The existence of a hazard,  The hazard must be recognized,
What are the tensions in cables ef and eg : The system shown anchors a stanchion of cable-suspended roof. If the tension in cable AB is 900 kN, what are the tensions in cables EF and EG?
What is the pressure in the tank : If 300 Kg of air is pumped into a previously empty 100 m^3 tank, and the temperature of the air in the tank is 25 deg C, then what is the pressure in the tank in N/m^2?
Explain what is the breakeven point for the new process : What is the breakeven point for this new process? Compare this process to the process proposed in the previous problem. For what volume of demand should Patricia choose this process?
Sketch hoop and radial stresses in the wall of cylinder : the cylinder is made from steel where yield stress= 240 MPa and v=0.3. Subsequently sketch the hoop and radial stresses in the wall of the cylinder.
Multi-employer worksite policy : Describe and discuss OSHA’s multi-employer worksite policy with regards to employers who control a given worksite, employers whose employees are exposed to a hazard, and employers who create a given hazard.
Concepts from the strategic management : A ppt consisting of 5 slides 4 points per slide and a memo elaborating on the slides for the memo - Should be based on concepts from the strategic management textbook by Dess Lumpkin Eisner and McNamara.
Find out the average length of the waiting line : Determine the average length of the waiting line and the waiting time. Discuss the quality implications of your results. If you decide that the quality of the service could be improved, indicate what things you might do to improve quality.
Freedom to comment reflection : describing a situation in which you, as a member of a group, strongly disagreed with the actions of the group based on ethical grounds. Did you feel free to voice your opinion, or did you feel pressure to conform to the group?

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  Find the stagnation pressure loss

Consider a supersonic wind tunnel with test section Mach number of 2 and fixed geometry diffuser designed to operate with minimum stagnation pressure losses (smallest diffuser area).

  Locate the initial and final states on a sketches

water contained in a closed, rigid tank, initially saturated vapor at 200C, is cooled to 100C. determine the initial and final pressure, each in bar. locate the initial and final states on a sketches of the p-v and T-v digrams.

  Calculate the diffusion co-efficient

The diffusion constant (Do) and activation energy (Q) of C in BCC Fe is 0.01 cm2/sec and 80kJ/mol respectively. In FCC Fe, the values are 0.21 cm2/sec and 148kJ/mol. At exactly 910oC these two phases can co-exist.

  What is the difference between mixed and unmixed flow

What is the difference between mixed and unmixed flow in heat exchangers?

  What is the specific volume

what is the specific volume, internal energy (kj/kg) and enthalpy (kj/kg) for water at 1.8 mpa and 120 Degrees C? Locate the state on p-v diagram and document assumptions.

  Design a container using differentiation

design a container using differentiation that has a volume of 2500 litres. it must use the minimum amount of material.

  What is the tension in the tow cable

the 3000 lb car and the 4600 lb tow truck are stationary. the muddy surface on which the car rest exerts a negligible friction force on the car. what is the tension in the tow cable.

  Create a design of rankine cycle

your job is to create a design of Rankine cycle that create the most possible power from this heat source . you may use any working fluid for which you can find the properties , assume the turbines 92% efficient and pumps 85%

  Identify the information used to make the decision

Given a simulator or actual device, identify if a control loop is in control or out of control and identify the information used to make the decision

  Explain what is the efficiency of the machine

Important information about Multipal choice question on mechanics, A machine is supplied energy at a rate of 4,000 W and does useful work at a rate of 3,760 W. What is the efficiency of the machine?

  Explain entropy generation in a steam turbine

Entropy Generation in a Steam Turbine, Steam at a rate of 15lbm/s enters a turbine at 500 Psia, 800f and exits at 5 Psia. For a reversible, adiabatic process (iseentropic)

  Ewb project

write a reflective assessment of how you rate yourself against these competencies and Describe the main learning outcomes that this course and the EWB project have generated for you over the semester. Have any of these learning outcomes been a ..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd