Shell-and-tube heat exchanger is used to cool flow of steam

Assignment Help Mechanical Engineering
Reference no: EM13711598

A shell-and-tube heat exchanger is used to cool a flow of steam using a stream of cooling water. The steam enters the heat exchanger at 0.1 bar and a quality of 91% (state 1), and exits as a saturated liquid at the same pressure (state 2). The mass flow rate of the steam is 2.6 · 105 kg/hour. The cooling water enters the heat exchanger at 5 MPa and 15oC (state 3) and exits at 38oC at the same pressure (state 4). The cooling water can be treated as an incompressible liquid. Neglect stray heat transfer and neglect kinetic and potential energy effects. As well, assume the system is operating under steady-state conditions.

a) Determine the mass flow rate of cooling water in kg/s.

b) Determine the rate of heat transfer between the steam and the cooling water in MW.

Reference no: EM13711598

Questions Cloud

Range of projectile and velocity on impact given inputs : (MATLAB) given a cannon ball that is shot upwards at an angle, the time taken for the cannon ball to hit the ground is: Write a single function that outputs the total time of flight, range of projectile and velocity on impact given inputs. Use the fu..
A woman is admitted to the emergency room : A woman is admitted to the emergency room because the tissues in her legs are retaining water. She is diagnosed with severe pitting edema-any pressure applied to the swollen tissue leaves a temporary indentation or "pit" in the tissue, even wh..
What is coefficient of restitution needed for good ammo : A "pumpkin chucker" designed for the annual pumpkin competition held near Millsboro, delaware every fall (first week of November) uses a pneumatic launcher (air cannon) to throw its pumpkin. It is important to know if your "ammunition", the pumpkin, ..
Difference between causes and effects in the swot analysis : Difference between causes and effects in the SWOT analysis.Causes are important, not effects. Once the SWOT Analysis is created, each group needs to construct the SWOT Bivariate Strategy Matrix.
Shell-and-tube heat exchanger is used to cool flow of steam : A shell-and-tube heat exchanger is used to cool a flow of steam using a stream of cooling water. The steam enters the heat exchanger at 0.1 bar and a quality of 91% (state 1), and exits as a saturated liquid at the same pressure (state 2). The mass f..
Briefly explain how gmos are created : Briefly explain how GMOs are created in your own words.
Fire truck draws water from an open constant-level reservoir : A fire truck draws water from an open constant-level reservoir through a hose of 0.2 ft2 cross section. The water is discharged from the pump through another 0.2 ft2 hose to a surge tank pressurized to 120 psig with air at the top. The pump adds 970 ..
Determine volume and height of cooling tower-effectiveness : A counter flow cooling tower cools 2000 gal/min water from 104 F to 85 F with 210,000 ft^3/min of air at 90 F Dry bulb Temperature and 76 F WBT . The Mass transfer coefficient -surface area product is hA= 123lbm/hr ft^3. Air mass flow rate per unit c..
Strained juice is concentrated in a vacuum evaporator : In a process for concentrating 1000kg of freshly extracted orange juice containing 12.5 wt% solids, the juice is strained, yielding 800kg of strained juice and 200kg of pulpy juice. The strained juice is concentrated in a vacuum evaporator to give an..

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  frictionless-piston-cylinder assembly

A closed, frictionless, piston-cylinder assembly contains 4 lbm of H20. Beginning with an initial volume of 10 ft^3, the H2O is compressed slowly until the volume has been reduced to 10 percent of the initial volume. During the process, heat transfer..

  Determine the maximum velocity reached

A 0.7-lb block rests on top of a 0.5-lb block supported by but not attached to a spring of constant 9 lb/ft. The upper block is suddenly removed. Determine (a) the Maximum velocity reached by the 0.5-lb block, (b) the maximum height reached by the..

  Estimate by what percent the average air-water density is

the presence of raindrops in the air during a heavy rainstorm increases the average density of the air-water mixture.

  Find the pitch diameter of the pinion

find: a) the pitch diameter of the pinion. b) the pitch diameter of the gear. c) the output torque of the gear. d) the minimum length of the key used to attach the gear?

  A 250 g 230-cm-diameter plastic disk is spun on an axle

a 250 g 23.0-cm-diameter plastic disk is spun on an axle through its center by an electric motor. what torque must the

  Low-velocity steam with negligible kinetic energy enters an

low-velocity steam with negligible kinetic energy enters an adiabatic nozzle at 300 c and 3 mpa. the steam leaves the

  The field-circuit resistance and armature-circuit

the field-circuit resistance and armature-circuit resistance of a 10-hp 115-v motor are 90 ohms and 0.08 ohms

  A solid shaft l 19 m long is supported between two bearings

a solid shaft l 1.9 m long is supported between two bearings. the shaft rotates at 250 rpm. a 20 degree involute gear

  Aweightless box with a 04m by 04m square base is floating

a weightless box with a 0.4m by 0.4m square base is floating horizontally on the water surface. it contains a 0.2m

  This unit cell is similar to the face-centered cubic unit

consider the cuau crystal structure. it can be described as a simple cubic lattice with a basis of cu 0 0 0 cu 1 2 1 2

  An open belt drive connects two pulleys 12 and 05m diameter

an open belt drive connects two pulleys 1.2 and 0.5m diameter on parallel shafts 3.6m apart. the belt has a mass of

  A circular fin of uniform cross section with diameter of

a circular fin of uniform cross section with diameter of 10mm and length of 50mm is attached to a wall with surface

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd