Shear stresses by solving the eigen value problem

Assignment Help Mechanical Engineering
Reference no: EM13706958

Write a MATLAB program that takes an input of the stress state in 3D. The program should

1) Create the stress tensor.

2) Calculate the principal normal and shear stresses by solving the Eigen value problem.

3) Calculate the Eigen vectors and use them to calculate the angle of the principal plane.

Use the answers you got from problems (1) and (2) in your code for debugging and checking your answers.

Reference no: EM13706958

Questions Cloud

How long does it take the projectile to fall onto table top : If a projectile is launched horizontally (launching angle = 0.0) at a height of y above the table top, and it falls on the table top, How long does it take the projectile to fall onto the table top
Determine what should be the resistance : The capacitor in an RC circuit has a capacitance of 23.6 µF. what should be the resistance
Type supercritical power plant has turbine inlet steam : An advanced-type supercritical power plant has turbine inlet steam at 7000 psia and 1400 F, double reheat at 1600 psia and 400 psia, both to 1200 F, and condenser at 1 psia. The three turbine sections have polytropic efficiencies of 0.93, 0.91, and 0..
What is the mass of the ball : A Styrofoam ball of radius 35 cm falls with a terminal speed of 5.3 m/s. What is the mass of the ball
Shear stresses by solving the eigen value problem : Write a MATLAB program that takes an input of the stress state in 3D. The program should Create the stress tensor. Calculate the principal normal and shear stresses by solving the Eigen value problem.
Find the magnitude of the resultant vector a+b : Consider two vectors A and B and their resultant A+B. The magnitudes of the vectors A and B are, respectively, 14.1 and 6 and they act at 110 degree to each other. Find the magnitude of the resultant vector A+B
Nyquist frequency in rpm for the rotation of the wheel : In the physical aliasing demonstration, the small DC electric motor rotated the wheel at 1500 RPM. What would be the Nyquist frequency in RPM for the rotation of the wheel?
Find the ratio of the outer area to inner area of the shell : A spherical shell is formed by taking a solid sphere of radius 25.0cm and hollowing out a spherical section from the shell's interior. What is the ratio of the outer area to the inner area of the shell
Estimate the cost of energy lost to heat per hour per meter : A small city requires about 10 MW of power. Suppose that instead of using high-voltage lines to supply the power, the power is delivered at 120 V. estimate the cost of the energy lost to heat per hour per meter

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  Design a packed tower for the absorption so2 from air the

design a packed tower for the absorption so2 from air. the so2 feed contain 0.0016 mol frac a into pure water in column

  Calculate the minimum flow rate

A solution is pumped through a 5cm diameter stainless steel pump.

  Compute the percentage ionic character of interatomic bond

Compute the percentage ionic character of the interatomic bond for each of the following compounds: MgO, GaP, CsF, CdS, and FeO

  Hot combustion gases enter a gas turbine at 8mpa and 1500 k

hot combustion gases enter a gas turbine at .8mpa and 1500 k at a rate of 2.1 kgs and exit at .1 mpa and 800 k. if heat

  Determine whether erosion will take place if the maximiun

an earthen channel n0.03 has a bed width of 5.0 m a water depth h 1.5 m a 45deg side slope and a channel slope of

  Determine the maximum centric force which can be applied is

a 1.5 m concrete post is reinforced with six steel bars each with a 28mm diameter. knowing that es 200 gpa and ec 25

  Calculate the value of forces

Calculate the value of forces P and Q for each test using the method of sections technique.

  Determine the weight of a part having the same modulus of

a titanium alloy with a modulus of elasticity of 16 x 106 psi is used to make a 1000 lb part for a manned space

  Determine the normal stress on a plane inclined at an angle

the principal stresses at a given point are 10 mpa a2 -100 mpa. sketch mohrs circle for this state of stress and

  Determine 1 the energy flow rate of the oil at the inlet 2

an oil pump is powered by a 5kw electric motor. the pressure at the outlet and the inlet of the pump at full load is

  Would it be a possible to use a normal domestic

would it be a possible to use a normal domestic refrigerator as a heat source for a small hot tub or whirlpool? if so

  Calculate spring stiffness

Calculate spring stiffness for which the oscillator becomes unstable (gravity in the negative y direction) verify with SW Simulation (study 1)

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd