Obtain the surface and contour plots for the temperature

Assignment Help Electrical Engineering
Reference no: EM13270289

A square metal plate is heated to 80 degrees celsius at the corner corresponding to x = y = 1. The temperature distribution in the plate is described by

T = 80e^(-(x-1)^2)*e^(-3(y-1)^2)

Obtain the surface and contour plots for the temperature. Label each axis. What is the temperature at the corner corresponding to x = y = 0?

Reference no: EM13270289

Questions Cloud

Define the ph of a solution prepared by diluting : Calculate the pH of a solution prepared by diluting 2.5 mL of 1M acetic acid up to a final volume of 100 mL (pka 4.76)
Determine acceleration of the proton when it has a velocity : a proton moves through a region containing a uniform electric field given by E=50.0 v/m and a uniform magnetic field B=(0.200+.300+.400)T. Determine the acceleration of the proton when it has a velocity v=10.0m/s
How much work was done by the person who pulled on the cord : A small block with a mass of 0.117 kg is attached to a cord passing through a hole in a horizontal frictionless surface, How much work was done by the person who pulled on the cord
Define what is the ph of rainwater in equilibrium : Assuming levels of atmospheric CO2 are 390 ppm CO2, what is the pH of rainwater in equilibrium with the atmosphere for the pre-industrial atmospheric CO2 concentration of 280 ppm,v.
Obtain the surface and contour plots for the temperature : A square metal plate is heated to 80 degrees celsius at the corner corresponding to x = y = 1. The temperature distribution in the plate is described by T = 80e^(-(x-1)^2)*e^(-3(y-1)^2) Obtain the surface and contour plots for the temperature.
Determine output y using complex domain analysis technique : Consider a continuos time LTI system with step response given by ys(t) = tu(t) - (t - 2)u(t-2). Determine the output y(t) if the input to the system is given by x(t) = u(t) - u(t - 2) using complex domain (not time domain) analysis techniques.
What is the angular magnification of the telescope : The eyepiece of a refracting telescope (see Fig.34.53 in the textbook) has a focal length of 9.00 cm. What is the angular magnification of the telescope
Explain the aqueous solubility of dissolved organic matter : Explain the effect of pH on the aqueous solubility of dissolved organic matter (use the 13C NMR spectra on the International Humic Substances Society as your primary reference). Speculate on how DOM fractionation would change crossing a riverine (..
Civil rights movement-second reconstruction : The Civil Rights Movement is often described as the Second Reconstruction and what do you think is meant by this description, and do you think it is fair?

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Find the value of peak amplitude in a constellation diagram

A constellation diagram has four points located at (2,2), (-2,2), (-2, -2), and (2, -2) on the I(in-phase)-Q(quadrature phase) plane. Find the value of peak amplitude and the type of modulation this diagram represents.

  Implement ckt using single decorder with active high outputs

A combinational logic circuit has 3 outputs as described below: F1=Minterm(0,3,4) F2= minterm(1,2,7) F3= Maxterm=(0,1,2,4) Implement the circuit using a single decorder with active high outputs and external 2 input OR gates

  Find the slopes and the interceptions at the voltage axis

An abrupt p-n junction has a doping concentration of 1015, 1016, or 1017 cm-3 on the lightly doped n-side and of 1019 cm-3 on the heavily doped p-side. Obtain series of curves of 1/C2 versus V, where V ranges from -4 to 0V in steps of 0.5V.

  Find complement of a 1s complement sum checksum computation

Incremental Update. Typically, after every hop at least one packet header field (e.g., a packet's time-to-live field) needs to be overwritten. Because the checksum is a simple complement of a 1s complement sum, it turns out that when, for instance..

  Calculate the impulse response using laplace transforms

using 1/(s+2)(s+4) + c find when the poles are repeated and use that value to calculate the impulse response using laplace transforms. Calculate the step response when c = 10 using Laplace transforms.

  Write an arduino program that displays the sequence

A single, common-anode, 7-segment LED is connected to the Arduino Connector J1 through current-limiting resistors. The diagram in Figure 1 shows the mapping of the pins of the connector to the pins of the 7-segment.

  What is the maximum load current that can be supplied

Two parallel connected 10 kV to 120 V 60 Hz single phase transformers supply a varying load. Assuming 0.85 PF, what is the maximum load current that can be supplied by this parallel combination of transformers wihout overloading either of them

  Calculate the final voltage on the capacitor

The switch in the circuit has been in position a for a long time. At t=0 the switch is moved to position b. A.Calculate the initial voltage on the capacitor ifv = 200V , and i = 1.9mA .  B. Calculate the final voltage on the capacitor. C. Calculate t..

  What is the period for a signal with pwmper

A HCS12 embedded timer is in PWM mode. If the E-clock is 24 MHz, and a scaler value of 16 is selected, what is the period for a signal with PWMPER = 0x75

  Determine the generated voltage and the kw rating

A four pole DC machine has a wave winding of 300 turns. The flux per pole is .025 webers. The DC machine rotates at 1000 RPM. Determine the generated voltage and the kW rating if the current through the turn is 25 amps.

  Determine how far backed-off must the amplifier operate

If the SNR must be greater than 40 dBm, how far backed-off must the amplifier operate. Assume noise comes from a third-order intermodulation between two interferers with the same power level as the wanted signal.

  What then is the indicated temperature

Suppose the RTD of (108.1 Ohms) has a dissipation constant of 25mW/°C and is used in a circuit that puts 8 mA through the sensor. If the RTD (108.1 Ohms) is placed in a bath at 100°C, what resistance will the RTD have

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd