User Account

All Pages

Multisim single frequency analysis

Assignment Help Other Engineering
Reference no: EM131077728

  1. Watch the videos

    • Week 3 Video Lecture - Multisim Single Frequency Analysis
  1. Consider the circuit below:
  2.  

  3. For the circuit above, determine the following (express all answers in phasor form):

  4. XC
  5. Zeq
  6. IT
  7. R1
  8. IC1
  • Construct the circuit with MultiSIM using a 5% tolerance for the resistor and the capacitor. Adjust the frequency according to the table below and obtain measurements from MultiSIM using AC Analysis and express in polar form.
    Frequency IT IR1 IC1
    100 Hz      
    500 Hz      
    1000 Hz      
    1500 Hz      
    10000 Hz      
    20000 Hz      
  • Discuss the following:
    1. Describe the relationship between the frequency and IT.
    2. What effect does frequency have on Zeq?
    3. How could the circuit be modified to bring the phase angle closer to 0??
    4. How could the circuit be modified to bring the phase angle closer to -90??

Watch the videos

Week 3 Video Lecture - Multisim Single Frequency Analysis

Consider the circuit below:

For the circuit above, determine the following (express all answers in phasor form):

  1. XC
  2. Zeq
  3. IT
  4. R1
  5. IC1

Construct the circuit with MultiSIM using a 5% tolerance for the resistor and the capacitor. Adjust the frequency according to the table below and obtain measurements from MultiSIM using AC Analysis and express in polar form.

Frequency

IT

IR1

IC1

100 Hz

      

500 Hz

      

1000 Hz

      

1500 Hz

      

10000 Hz

      

20000 Hz

      

Discuss the following:

  1. Describe the relationship between the frequency and IT.
  2. What effect does frequency have on Zeq?
  3. How could the circuit be modified to bring the phase angle closer to 0â-‹?
  4. How could the circuit be modified to bring the phase angle closer to -90â-‹?

Reference no: EM131077728

Questions Cloud

Introduction of new fast food outlet : A campus program evenly enrolls undergraduate and graduate students. If a random sample of 4 students is selected from the program to be interviewed about the introduction of new fast food outlet on the ground floor of the campus building,
Find the employee''s expected earnings : Find the employee's expected earnings.
How would about estimating effect size and statistical power : Make up and discuss research examples corresponding to the various techniques introduced throughout this course. Describe a plausible study for each of the following statistical procedures, indicating how it would apply and what results you would ..
Information to find the p-value : Assume that the significance level is α=0.1. Use the given information to find the P-value and the critical value(s). The test statistic of z=1.95 is obtained when testing the claim that p>0.8.
Multisim single frequency analysis : Construct the circuit with MultiSIM using a 5% tolerance for the resistor and the capacitor. Adjust the frequency according to the table below and obtain measurements from MultiSIM using AC Analysis and express in polar form.
Find the value of the test statistic : A random sample of 44 adult females has white blood cell counts with a mean of 8.95 and a standard deviation of 3.16. Find the value of the test statistic.
Compute this student''s grade-point average : Compute this student's grade-point average.
Circuit in multisim and run a single frequency analysis : Consider the circuit demonstrated in this week's presentation. Analyze the circuit to determine the following (include both polar and complex forms where applicable):
Describe responsibilities of the supervisee and supervisor : What questions would you have for your supervisor about any of the items included, if you were the supervisee receiving this agreement at your fieldwork site? How important would it be for you to have this type of agreement in place with your supe..

Reviews

Write a Review

Other Engineering Questions & Answers

  Describe and compare the ventilation systems

State reasons for the popularity of decline mining in modern operations. What factors need to be taken into account in deciding the cut off depth beyond which shaft operations should be used instead of decline access.

  Summarise the steps in the development of an open pit mine

Draw a plan of a typical strip mine showing all operational features and equipment - Summarise the steps in the development of an open pit mine. b. What are the purposes of safety benches?

  How did presidential addresses and supreme court rulings

Conduct an Internet search to answer the question: How did Presidential addresses and Supreme Court rulings begin to change the lives of the American people beginning in the mid-20th century?

  Find the percentage error of this circuit as a sine shaper

The two-diode circuit shown in Fig. can provide a crude approximation to a sine-wave output when driven by a triangular waveform. To obtain a good approximation, we select the peak of the triangular waveform, V, so that the slope of the desired si..

  Determine the von mises distribution in the plate

The plate is uniformly loaded from the bottom surface with a pressure load of 15 kN/m2. Elastic modulus is E = 210 x 109 N/m2 and Poisson's ratio is v = 0.33. Determine the von Mises distribution in the plate.

  What is the cost sportstuff.com incurs it all warehouses

What is the cost SportStuff.com incurs it all warehouses leased are in St. Louis and what supply chain network configuration do you recommend for SportStuff.com? Why?

  Doing research in tool life of solid carbide endmills

Doing research in tool life of solid carbide endmills and I was looking at your formulas.

  How can a fieldbus system be implemented

How can a fieldbus system be implemented in an existing HART system - how can multiple variables be measured using a single fieldbus instrument?

  Disc profiles in order to get job

Part 1: Write a brief essay describing two ways you would effectively use the DiSC profiles in order to get job.

  Determine the minimum cable force t and critical angle

Determine the minimum cable force T and critical angle ? which will cause the tow truck to start tipping, i.e., for the normal reaction at A to be zero. Assume that the truck is braked and will not slip at B. The truck has a total mass of 4 Mg and..

  Food nano technology and emulsion technology due dateformat

due date ltbrgtformat individual work ? written literature review ltbrgtlength 2000 words ltbrgtdescription the major

  Write an assembly language program to load register

Write an assembly language program to load Register A with number 7, and Register B with number 8. Add these two registers

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd