Motor is used to raise

Assignment Help Mechanical Engineering
Reference no: EM13705232

A 100-watt motor (60% efficient) is used to raise a 100-kilogram load 5 meters into the air. How long, in units of seconds, will it take the motor to accomplish this task?

Reference no: EM13705232

Questions Cloud

The family income is very high, as it is in your case : Imagine you are applying for a Visa credit card and asking for a credit limit of $15,000. While there is no set policy for reviewing and raising credit limits, the company's policy explicitly states that new customers may only receive a $7,500 ..
Describe the earliest chordates from early tunicate relative : Describe the earliest chordates from early tunicate relatives through the development of vertebrate jaws and a transition to land.
The main pros and cons of being an entrepreneur : Describe how your perspective has changed related to corporate entrepreneurship.  What do you think are the main pros and cons of being an entrepreneur?
What is the adjusted basis of the new residence : During 2006, Ted and Judy, a married couple, decided to sell their residence, which had a basis of $162,000. They had owned and occupied the residence for 11 years.
Motor is used to raise : A 100-watt motor (60% efficient) is used to raise a 100-kilogram load 5 meters into the air. How long, in units of seconds, will it take the motor to accomplish this task?
What is an appropriate way of handling conflicts : Being assigned as a project manager, you noticed during project execution that conflicts arise in the team on both technical and interpersonal levels. What is an appropriate way of handling conflicts?1 o Conflicts distract the team and disrupt ..
The organization selected for resource dependency theory : Compose a 1-2 page summary paper identifying the organization selected for Resource Dependency Theory and Institutional Theory analysis paper due in Unit 10. Describe the organization you selected. Provide a brief history of the organization you ..
Adapting to workplace changes in professionalism : Defining and understanding the elements of a group culture is essential to forging a professional identity either online or in person. These elements are important because they reflect how professionals interact, whether online or in person.
Writing a literature review on consumer privacy : Writing a literature review on consumer privacy. Only experienced tutors should respond. The literature review should achieve the following: Use articles from peer-reviewed journal publications on consumer privacy.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A rankine power cycle operates with an open feedwater

a rankine power cycle operates with an open feedwater heater. the boiler pressure is 6.0 mpa. a superheater provides a

  How much heat is rejected to the cooling system

steam with 88.6% quality and a flow rate of 750 kg/s enters a condenser operating @ 75 KPa. Saturated liquid leaves the condenser. How much heat is rejected to the cooling system.

  An aqueous ester hydrolysis reaction a -gt b c has k 002

an aqueous ester hydrolysis reaction a -gt b c has k 0.02 min-1 and an equilibrium constant of 10 with all

  If the velocity out the 2-cm-diameter tube is 15 ms

water flows into a volume that contains a sponge with a flow rate of 0.02 m3s. it exits the volume through two tubes

  The lowest temperature that has been achieved is about 1

the lowest temperature that has been achieved is about 1 times 10-6 k. to achieve this an additional stage of cooling

  Te local acceleration of gravity is 981 ms2 determine the

a gas is contained in a vertical frictionless pixton-cylinder. the piston m 10 kg a- 7.5 x 10-3 m2 is attached to a

  Argon gas enters an adiabatic compressor under steady flow

argon gas enters an adiabatic compressor under steady flow conditions at 12o kpa and 30 c with a velocity of 20 ms and

  The thermal conductivities of cast iron and enamel are 50

an electric hot plate is maintaned at a temperature of 350 and is used to keep the solution just boiling at 95. the

  If the pressure at the final state is 300 kpa determine a

two tanks tank a and tank b are separated by a partition. initially tank a contains 2-kg steam at 1 mpa and 300degc

  A solid aluminium sphere of emissivityepsilon is initially

a solid aluminium sphere of emissivityepsilon is initially at an elevated temperature and is cooled by placing it in

  Assuming neglible heat transfer between the bucket and the

a one kg metal part specific heat 0.7 kjkg k initially at 1234k is quenched in a bucket containing 20 gallons of water

  At a surface cutting speed of 190 mmin the productive tool

at a surface cutting speed of 190 mmin the productive tool life was 60 minutes. at a surface cutting speed of 225 mmin

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd